HCPL-0466#500 Avago Technologies US Inc., HCPL-0466#500 Datasheet - Page 10

• Manufacturer Part Number: HCPL-0466#500
• Description: OPTOCOUPLER IPM/DRVR 8-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-0466#500

• Output Type: Open Collector
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 15mA
• Data Rate: 1MBd
• Propagation Delay High - Low @ If: 200ns @ 10mA
• Current - Dc Forward (if): 25mA
• Input Type: DC
• Mounting Type: Surface Mount
• Configuration: 1 Channel
• Isolation Voltage: 3750 Vrms
• Current Transfer Ratio: 90 %
• Maximum Propagation Delay Time: 650 ns
• Maximum Forward Diode Voltage: 1.8 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Forward Diode Current: 20 mA
• Maximum Continuous Output Current: 15 mA
• Maximum Power Dissipation: 145 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

All Avago data sheets report the creepage and clearance
inherent to the optocoupler component itself. These di-
mensions are needed as a starting point for the equip-
ment designer when determining the circuit insulation
requirements. However, once mounted on a printed
circuit board, minimum creepage and clearance require-
ments must be met as specified for individual equipment
standards. For creepage, the shortest distance path along
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
*Refer to the optocoupler section of the Designer's Catalog, under regulatory information (IEC/EN/DIN EN 60747-5-2) for a detailed description of
Method a and Method b partial discharge test profiles.
Notes:
These optocouplers are suitable for "safe electrical isolation" only within the safety limit data. Maintenance of the safety data shall be ensured by
means of protective circuits.
Insulation Characteristics are per IEC/EN/DIN EN 60747-5-2.
Surface mount classification is Class A in accordance with CECC 00802.
10
Description
Installation classification per
DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤150 V rms
for rated mains voltage ≤300 V rms
for rated mains voltage ≤450 V rms
for rated mains voltage ≤600 V rms
for rated mains voltage ≤1000 V rms
Climatic Classification
Pollution Degree
(DIN VDE 0110/1.89)
Maximum Working
Insulation Voltage
Input to Output Test Voltage,
Method b* V
100% Production Test with t
1 sec, Partial Discharge < 5pC
Input to Output Test Voltage,
Method a* V
Type and Sample Test, t
Partial Discharge < 5pC
Highest Allowable Overvoltage*
(Transient Overvoltage, t
Safety Limiting Values – maximum
values allowed in the event of a fail-
ure, also see Thermal Derating curve.
Insulation Resistance at T
V
IO
Case Temperature
Input Current
Output Power
= 500 V
IORM
IORM
x 1.5 = V
x 1.875 = V
m
ini
S
PR
= 60 sec,
,
= 10 sec)
,
PR
m
,
=
P
Symbol
I
S OUTPUT
V
V
S INPUT
V
V
IORM
IOTM
T
R
PR
PR
S
S
Option 060
55/100/21
HCPL-0466
≥ 10
1050
4000
560
840
150
150
600
I-IV
I-III
2
9
the surface of a printed circuit board between the solder
fillets of the input and output leads must be considered.
There are recommended techniques such as grooves
and ribs which may be used on a printed circuit board to
achieve desired creepage and clearances. Creepage and
clearance distances will also change depending on fac-
tors such as pollution degree and insulation level.
55/100/21
Option 060
HCPL-4506
1181
6000
≥10
630
945
175
230
600
I-IV
I-IV
I-III
2
9
55/100/21
HCPL-J456
1670
1336
6000
≥10
891
175
400
600
I-IV
I-IV
I-III
I-III
2
9
55/100/21
HCNW4506
1414
2652
2121
8000
≥10
150
400
700
I-IV
I-IV
I-IV
I-IV
I-III
2
9
V
V
V
V
Unit
mW
mA
peak
peak
peak
peak
°C
Ω