HCPL-2200#060 Avago Technologies US Inc., HCPL-2200#060 Datasheet - Page 10

• Manufacturer Part Number: HCPL-2200#060
• Description: OPTOCOUPLER 1CH 2.5MBD VDE 8-DIP
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-2200#060

• Package / Case: 8-DIP (0.300", 7.62mm)
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 25mA
• Data Rate: 2.5MBd
• Propagation Delay High - Low @ If: 210ns @ 3mA
• Current - Dc Forward (if): 10mA
• Input Type: DC
• Output Type: Tri-State
• Mounting Type: Through Hole
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 25 mA
• Maximum Fall Time: 15 ns
• Maximum Forward Diode Current: 10 mA
• Maximum Rise Time: 55 ns
• Output Device: Logic Gate Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 5 MBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Power Dissipation: 210 mW
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

10
Notes:
1. Derate total package power dissipation, P
2. Duration of output short circuit time should
3. Device considered a two-terminal device:
4. The t
Figure 1. Typical logic low output voltage vs.
temperature.
Figure 4. Typical input diode forward
characteristic.
0.001
1000
linearly above 70 C free air temperature at a
rate of 4.5 mW/ C.
not exceed 10 ms.
pins 1, 2, 3, and 4 shorted together and pins
5, 6, 7, and 8 shorted together.
from the 50% point on the leading edge of
the input pulse to the 1.3 V point on the
leading edge of the output pulse. The t
propagation delay is measured from the
0.01
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
100
1.0
0.1
10
0
-60
1.1
PLH
-40
propagation delay is measured
V
F
T
1.2
A
– FORWARD VOLTAGE – V
-20
V
– TEMPERATURE – °C
+
–
F
I
F
0
1.3
20
V
I
V
40
1.4
F
CC
O
= 0 mA
= 6.4 mA
T
= 4.5 V
60
A
= 25 °C
1.5
80
PHL
100
T
,
Figure 2. Typical logic high output current vs.
temperature.
INPUT
MONITORING
NODE
5. When the peaking capacitor is omitted,
6. CM
Figure 5. Test circuit for t
50% point on the trailing edge of the input
pulse to the 1.3 V point on the trailing edge
of the output pulse.
propagation delay times may increase by
100 ns.
common mode voltage that can be
sustained with the output voltage in the
logic low state (V
maximum rate of fall of the common mode
voltage that can be sustained with the
output voltage in the logic high state
(V
-1
-2
-3
-4
-5
-6
-7
-8
PULSE GEN.
0
t
f = 100 kHz
10 % DUTY
r
-60
O
V
= t
CYCLE
L
R
> 2.0 V).
O
is the maximum rate of rise of the
1
f =
= 5 V
-40
INPUT I
5 ns
T
OUTPUT
V
A
O
V
-20
O
– TEMPERATURE – °C
I
F
C
120 pF
V
= 2.4 V
1
F
O
=
0
O
= 2.7 V
< 0.8 V). CM
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C
ALL DIODES ARE 1N916 OR 1N3064.
I
1
2
3
4
20
F
(ON)
R
PLH
I
HCPL-2200
V
I
40
F
, t
CC
= 5 mA
2.15 k
1.6 mA
PHL
t
= 4.5 V
60
PLH
H
, t
is the
GND
r
V
, and t
80
CC
t
1.10 k
PHL
3 mA
100
8
7
6
5
1 AND
f
.
V
CC
681
5 mA
C
2 .
Figure 3. Output voltage vs. forward input
current.
7. Use of a 0.1 F bypass capacitor connected
8. In accordance with UL1577, each
OUTPUT V
MONITORING
NODE
50 % I
1.3 V
between pins 5 and 8 is recommended.
optocoupler is proof tested by applying an
insulation test voltage 4500 V rms for one
second (leakage detection current limit, I
100% production test for partial discharge
(Method b) shown in the IEC/EN/DIN EN
60747-5-2 Insulation Characteristics Table, if
applicable.
5 A). This test is performed before the
C
15 pF
5
4
3
2
1
0
2
I
0 mA
V
0
F
F
I
OH
OL
=
(ON)
(ON)
V
OL
= 6.4 mA
O
I
F
5 k
– INPUT CURRENT – mA
0.5
D
1
5 V
V
T
A
CC
619
= 25 °C
D
D
D
1.0
= 4.5 V
2
3
4
I
OH
= -2.6 mA
1.5
2.0
I-O