ACPL-074L-060E Avago Technologies US Inc., ACPL-074L-060E Datasheet
ACPL-074L-060E
Specifications of ACPL-074L-060E
Related parts for ACPL-074L-060E
ACPL-074L-060E Summary of contents
Page 1
... The optocouplers utilize the latest CMOS IC technol- ogy to achieve outstanding performance with very low power consumption. Basic building blocks of ACPL-071L and ACPL-074L are high speed LEDs and CMOS detector ICs. Each detector incorporates an integrated photodiode, a high speed transimpedance amplifier, and a voltage comparator with an output driver ...
Page 2
... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: ACPL-071L-500E to order product of Small Outline SO-8 package in Tape and Reel packaging in RoHS compliant. Example 2: ACPL-074L-000E to order product of Small Outline SO-8 package in tube packaging and RoHS compliant. ...
Page 3
... Package Dimensions ACPL-071L and ACPL-074L (Small Outline S0-8 Package XXXV 3.937 ± 0.127 YWW (0.155 ± 0.005 PIN ONE 0.406 ± 0.076 (0.016 ± 0.003) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) * 5.207 ± ...
Page 4
... SOLDERING 30 SEC. 30 SEC. 50 SEC. 100 150 TIME (SECONDS) Regulatory Information The ACPL-071L and ACPL-074L have been approved by the following organizations 20-40 SEC. UL Recognized under UL 1577, component recognition pro- gram, File E55361. RAMP-DOWN 6 °C/SEC. MAX. CSA Approved under CSA Component Acceptance Notice #5, File CA88324 ...
Page 5
Insulation and Safety Related Specifications Parameter Symbol Minimum External Air L(I01) Gap (Clearance) Minimum External L(I02) Tracking (Creepage) Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance CTI (Comparative Tracking Index) Isolation Group All Avago Technologies data sheets report the creepage ...
Page 6
IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (Option 060) Description Installation classification per DIN VDE 0110/1.89, Table 1 for rated mains voltage ≤150 V rms for rated mains voltage ≤300 V rms Climatic Classification Pollution Degree (DIN VDE 0110/1.89) Maximum Working ...
Page 7
... V ≤ +3.3V. DD Part Number Min. Typ. 1.3 1 0.35 0.2 4.5 ACPL-071L 4.1 ACPL-074L 8.3 ACPL-071L 3.8 ACPL-074L 7.6 = –40°C to +105°C), 3.0V ≤ V ≤ 3.6V and 4.5 V ≤ +3.3V. DD Symbol Min. Typ. Max PHL PLH 50 t 66.7 PW |PWD | ...
Page 8
... Figure 2. Typical input threshold current vs. temperature =5. =3. - 100 o C Figure 4. Typical logic low O/P supply current vs. temperature for ACPL-074L. Units Test Conditions μA 45% RH DC, I 25°C A Vrms RH ≤ 50 min 25° 500 MHz 25° =20uA oL 5V 3.3V ...
Page 9
... Application Information Bypassing and PC Board Layout The ACPL-071L and ACPL-074L optocouplers are extreme- ly easy to use. ACPL-071L and ACPL-074L provide CMOS logic output due to the high-speed CMOS IC technology used. The external components required for proper operation are the input limiting resistor and the output bypass ca- pacitor. Capacitor values should be between 0.01 μ ...
Page 10
Propagation Delay, Pulse-Width Distortion and Propa- gation Delay Skew Propagation delay is a figure of merit which describes how quickly a logic signal propagates through a system. The propagation delay from low to high (t of time required for an ...
Page 11
... To limit the amount of current flowing through the LED recommended that a 210ohm resistor is connect series with anode of LED (i.e. Pin 2 for ACPL-071L and Pin 1 and 4 for ACPL-074L input signal. At 3.3V input signal recommended to connect 80ohm resistor in se- ries with anode of LED. ...
Page 12
R limit SHIELD + Pulse Gen. - Zo=50Ω Figure 13. Test circuit for common mode transient immunity and typical waveforms. R assumed Ω) and the limiting resistor (R For product information ...