HCPL-M452#500 Avago Technologies US Inc., HCPL-M452#500 Datasheet - Page 6

• Manufacturer Part Number: HCPL-M452#500
• Description: OPTOCOUPLER 1CH 1MBS TTL SO-5
• Manufacturer: Avago Technologies US Inc.

Specifications of HCPL-M452#500

• Input Type: DC
• Package / Case: 5-SOIC
• Number Of Channels: 1
• Voltage - Isolation: 3750Vrms
• Current Transfer Ratio (min): 20% @ 16mA
• Current Transfer Ratio (max): 50% @ 16mA
• Voltage - Output: 20V
• Current - Output / Channel: 8mA
• Current - Dc Forward (if): 25mA
• Output Type: Transistor with Vcc
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Output Device: Phototransistor
• Configuration: 1 Channel
• Current Transfer Ratio: 50 %
• Maximum Baud Rate: 1 MBps
• Maximum Forward Diode Voltage: 1.7 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Input Diode Current: 25 mA
• Maximum Power Dissipation: 100 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Vce Saturation (max): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

Switching Specifications
Over recommended temperature (T
All typicals at T
Notes:
1. Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C.
2. Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C.
3. Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C.
4. Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C.
5. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I
6. Device considered a two terminal device: pins 1 and 3 shorted together, and pins 4, 5 and 6 shorted together.
7. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V
8. Common transient immunity in a Logic High level is the maximum tolerable (positive) dV
9. The 1.9 k: load represents 1 TTL unit load of 1.6 mA and the 5.6 k: pull-up resistor.
10. The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
11. Use of a 0.1 PF bypass capacitor con nected between pins 4 and 6 is recommended.
6
Parameter
Propagation Delay
Time to Logic Low
at Output
Propagation Delay
Time to Logic High
at Output
Common Mode
Transient Immunity
at Logic High Level
Output
Common Mode
Transient Immunity
at Logic Low Level
Output
Bandwidth
current limit, I
to assure that the output will remain in a Logic High state (i.e., V
tolerable (negative) dV
(i.e., V
O
< 0.8 V).
A
= 25°C.
I-O
≤ 5 PA).
Symbol
t
t
|CM
|CM
BW
CM
PHL
PLH
/dt on the falling edge of the common mode pulse signal, V
H
L
|
|
Device
HCPL-
M452
HCPL-
M453
HCPL-
M452
HCPL-
M453
A
= 0°C to 70°C) V
Min.
15
15
Typ.*
0.2
0.6
1
30
1
30
3
CC
O
> 2.0 V). Common mode transient immunity in a Logic Low level is the maximum
= 5 V, I
Max.
0.8
1.0
0.8
1.0
F
= 16 mA unless otherwise specified.
Units
Ps
kV/Ps
MHz
CM
CM
O
to assure that the output will remain in a Logic Low state
, to the forward LED input current, I
Test Conditions
T
T
V
V
V
V
V
V
R
/dt on the rising edge of the common mode pulse, V
A
A
CM
CM
p-p
CM
CM
p-p
L
= 25°C
= 25°C
= 100 :, See Test Circuit
= 10 V
= 1500
= 10 V
= 1500
p-p
p-p
R
R
I
T
R
I
T
R
F
F
A
A
L
L
L
L
RMS
= 0 mA
= 16 mA
= 1.9 k:
= 1.9 k:
= 25°C
= 1.9 k:
= 25°C
= 1.9 k:
for 1 second (leakage detection
Fig.
5, 6, 10
5, 6, 10
11
11
8, 9
F
, times 100.
9
9
10
Note
8, 9
8, 9
CM
,