DMC-20434N-SEW Optrex America Inc, DMC-20434N-SEW Datasheet
DMC-20434N-SEW
Specifications of DMC-20434N-SEW
OP420NSEW
Related parts for DMC-20434N-SEW
DMC-20434N-SEW Summary of contents
Page 1
... Optical Specifications ..............................................................................6 4. I/O Terminal.............................................................................................8 5. Test..........................................................................................................10 6. Appearance Standards............................................................................11 7. Code System of Production Lot ..........................................................14 8. Type Number .........................................................................................14 9. Applying Precautions .............................................................................14 10. Handling Precautions .............................................................................15 Rev. Date DMC20434N-SEW (AU) No.97-0209 First Edition Sep 3, 1997 Final Revision ******* Table of Contents Revision History Page OPTREX CORPORATION ...
Page 2
... Outline Dimensions ： 70g max. Weight ： NSD-7141 LCD Type ： 6:00 Viewing Angle ： Electro Luminescence (EL) / White Backlight ： Dimensional Outline Drawings DMC20434N-SEW (AU) No.97-0209 ( STN / Neutral-mode / Transflective ) UE-34749 OPTREX CORPORATION OPTREX Page 2/15 ...
Page 3
... High Level V IH Input Voltage Low Level V IL Input Voltage High Level V OH Output Voltage Low Level V OL Output Voltage Supply Current I CC DMC20434N-SEW (AU) No.97-0209 Conditions Min. － -0.3 － 0 － -0.3 Conditions Min. － 4.5 Shown in 3.1 V =5.0V±10% 2 =5.0V± ...
Page 4
... Enable Rise/Fall Time Address Setup Time Address Hold Time Write Data Setup Time Write Data Hold Time Read Data Delay Time Read Data Hold Time RS R/W E DB0 ～ DB7 RS R/W E DB0 ～ DB7 DMC20434N-SEW (AU) No.97-0209 Symbol Conditions t Fig.1, 2 CYC PW Fig. Fig.1, 2 ...
Page 5
... Characteristics Parameter Conditions Input Voltage Input Frequency Current AC100Vrms, 400Hz Luminance of AC100Vrms, 400Hz Backlight Surface Life AC100Vrms, 400Hz Ta=20℃,60%RH Recommended Inverter : NEL-D32- 5.0V±10%, Produced by NEC ) DMC20434N-SEW (AU) No.97-0209 Min. － － － Min. － － － － － 34 2000 ...
Page 6
... ON signal is applied to. Vth2 : The voltage V O-P the segment which the OFF signal is applied to. V O-P × 〈 ON SIGNAL 〉 DMC20434N-SEW (AU) No.97-0209 Conditions Ta= 0℃ -V Ta=25℃ Ta=50℃ Ta=25℃, 1/16 Duty, 1/5 Bias, V Conditions θ= 0ﾟ, φ=－ﾟ ...
Page 7
... Duty, 1/5 Bias ﾟ 135 ﾟ 180 ﾟ 225 ﾟ 270 ﾟ ･Area shows typ. CR≧2 3.4.System Block Diagram Photometer #1980A WB Computer DMC20434N-SEW (AU) No.97-0209 f =4.5V, =46.9Hz ﾟ φ ( φ ﾟ） θ 180 ﾟ ...
Page 8
... EL 16 4.2.Example of Power Supply It is recommended to apply a potentiometer for the contrast adjust due to the tolerance of the driving voltage and its temperature dependence. MODULE DMC20434N-SEW (AU) No.97-0209 Function Power Supply (0V, GND) Power Supply for Logic Power Supply for LCD Drive Register Select Signal ...
Page 9
... Diagram 8 DB7 DB0 E R/W RS VCC VSS VEE EL EL DMC20434N-SEW (AU) No.97-0209 COM 16 20 characters × 4 lines Control LSI SEG 40 HD44780 or equivalent 4 Column Driver MSM5259 × 4 Bias Circuit EL Backlight OPTREX CORPORATION OPTREX SEG 160 or equivalent To LSI Page 9/15 ...
Page 10
... Note dew condensation to be observed. Note 4 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber. Note 5 : Vibration test will be conducted to the product itself without putting container. DMC20434N-SEW (AU) No.97-0209 Conditions 50℃±2℃, 96hrs (operation state) 0℃ ...
Page 11
... All directions for inspecting the sample should be within 45ﾟagainst perpendicular line. 6.2.Definition of applicable Zones A Zone : Active display area B Zone : Area from outside of "A Zone" to validity viewing area C Zone : Rest parts A Zone + B Zone = Validity viewing area DMC20434N-SEW (AU) No.97-0209 45 ﾟ A Zone Bezel Flame B Zone ...
Page 12
... Black and (1) Round Shape White Spots, Foreign Substances (2) Line Shape Total defects shall not exceed 5. 2 Air Bubbles (between glass & polarizer) Total defects shall not exceed 3. DMC20434N-SEW (AU) No.97-0209 Criteria Zone Dimension (mm ≦ 0.1 * 0.1 ＜ D ≦ 0.2 5 0.2 ＜ D ≦ 0.3 0 0.3 ＜ ...
Page 13
... Not to be conspicuous defects. 5 Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not defective. 6 Color Variation Not to be conspicuous defects. DMC20434N-SEW (AU) No.97-0209 Criteria 0.15 ≧ As per the sketch of left hand. Should not be connected to next dot. X (X+Y) / 2≦0.2mm Y (Less than 0 ...
Page 14
... The type number of module is specified on the back of module as follows. ＤＭＣ２０４３４ Etching or Printing 9.Applying Precautions Please contact us when questions and/or new problems not specified in this specifications arise. DMC20434N-SEW (AU) No.97-0209 □ □ Factory Number (Numeral) Factory Code (Alphabet) Production Week (1～ ...
Page 15
... Please consult OPTREX to specify the connection. Optrex shall not be responsible for any infringement of industrial property rights of third parties in any country arising out of the application or use of Optrex Products, except which directly concern the structure or production of such products. DMC20434N-SEW (AU) No.97-0209 (GND) is not specified in the module. SS ...