T-51512D121J-FW-A-AGN Optrex America Inc, T-51512D121J-FW-A-AGN Datasheet
T-51512D121J-FW-A-AGN
Specifications of T-51512D121J-FW-A-AGN
Related parts for T-51512D121J-FW-A-AGN
T-51512D121J-FW-A-AGN Summary of contents
Page 1
... INSPECTION STANDARDS 12 HANDLING PRECAUTIONS FOR TFT-LCD MODULE -- PACKAGING SPECIFICATION -- PRODUCTS NUMBER LABELING FORMS -- LAMP UNIT for 12.1” SVGA T-51512D121J-FW-A-AGN (AG) No. 2006-0045 Approved by (Quality Assurance Division) Checked by (ACI Engineering Division) S.Sano Prepared by (ACI Engineering Division) Item OPTREX CORPORATION First Edition Mar 10, 2006 ...
Page 2
... APPLICATION This specification applies to color TFT-LCD module, T-51512D121J-FW-A-AGN. These specification papers are the proprietary product of OPTREX and include materials protected under copyright of OPTREX. No part of this document may be reproduced in any form or by any means without the express written permission of OPTREX. OPTREX does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a product specified in this document ...
Page 3
... OVERVIEW T-51512D121J-FW-A-AGN is 12.1” color TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, driver ICs, control circuit, and backlight unit. By applying 6 bit digital data, 800 × 600, 262 K-color images are displayed on the 12.1” diagonal screen. Input power voltage is single 3.3V for LCD driving. ...
Page 4
... Power Supply Current for LCD Permissive Input Ripple Voltage High Logic Input Voltage Low *1) Power and signals sequence: t1 ≤ < t2 ≤ < t3 ≤ LCD Power Supply Logic Signal 0.1VCC Backlight Power Supply T-51512D121J-FW-A-AGN (AG) No. 2006-0045 SYMBOL VCC Note 1,2) op(Panel) T Note 2) op(Ambient) T ...
Page 5
... Lamp life time is defined as the time either when the brightness becomes 50% of the initial value, or when the starting lamp voltage does not meet the value specified in this table. *5) The life time of the backlight depends on the ambient temperature. The life time will decrease under low/high temperature. T-51512D121J-FW-A-AGN (AG) No. 2006-0045 td =37.9kHz, f =60.3Hz, f ...
Page 6
... Please use the inverter which has symmetrical current wave form as follows, The degree of unbalance: less than 10% The ratio of wave height: less than I I CURRENT WAVE FORM T-51512D121J-FW-A-AGN (AG) No. 2006-0045 2 ±10 High side peak PH PH The degree of unbalance = |I The ratio of wave height = I ...
Page 7
... GND 39 VCC 40 VCC and VD are not being used for timing control.*2)The shielding case is connected with GND. T-51512D121J-FW-A-AGN (AG) No. 2006-0045 Signal ground Clock signal for sampling catch data signal Signal ground Horizontal sync signal *1) Vertical sync signal *1) Signal ground Signal ground ...
Page 8
... Backlight-side connector: BHR-04VS-1 (JST) Inverter-side connector: SM04(4.0)B-BHS-1(JST) Pin No. [ Note ] VBLH - VBLL = VL T-51512D121J-FW-A-AGN (AG) No. 2006-0045 Symbol 1, 2 CTH 4 CTL OPTREX CORPORATION Function VBLH (High voltage) VBLL (Low voltage) Page 8/35 ...
Page 9
... DATA (R,G,B,DENA) Hold time Horizontal DENA Vertical [Note] 1) DATA is latched at fall edge of DCLK in this specification. 2) DENA (Data Enable) should always be positive polarity as shown in the timing specification. 3) DCLK should appear during all invalid period, T-51512D121J-FW-A-AGN (AG) No. 2006-0045 SYMBOL f CLK t CLK t WCL t WCH ...
Page 10
... Pixel Timing Chart DCLK DATA(R,G,B), DENA b. Horizontal Timing Chart DCLK DATA Invalid Data (R,G, DENA c. Vertical Timing Chart c. Vertical Timing Chart LINE DATA Invalid Data t VB DENA T-51512D121J-FW-A-AGN (AG) No. 2006-0045 t CLK t t WCH WCL 2.0V 0. Ｓ D Ｈ 2.0V 0.8V First Data ...
Page 11
... MAGENTA 1 YELLOW 1 WHITE 1 RED(1) 0 RED(2) 0 RED RED(62) 1 RED(63) 1 GREEN(1) 0 GREEN(2) 0 GREEN GREEN(62) 0 GREEN(63) 0 BLUE(1) 0 BLUE(2) 0 BLUE BLUE(62) 0 BLUE(63) 0 [Note] 1) Definition of gray scale Color (n) --- n indicates gray scale level. Higher n means brighter level. 2) Data 1:High, 0: Low T-51512D121J-FW-A-AGN (AG) No. 2006-0045 R DATA LSB MSB ...
Page 12
... Display Position and Scan Direction D(X,Y) shows the data number of input signal for LCD panel signal processing PCB. SC:Low D(1,1) D(800,1) D(800,600) D(1,600) T-51512D121J-FW-A-AGN (AG) No. 2006-0045 SC:High D(800,600) CN2 D(800,1) OPTREX CORPORATION ...
Page 13
... BLOCK DIAGRAM CN1 Timing signal Display data Timing Controller Power Power Supply Circuit T-51512D121J-FW-A-AGN (AG) No. 2006-0045 G1 G2 TFT-LCD G600 Drivers(source) CCFL OPTREX CORPORATION CN2 Page 13/35 ...
Page 14
... MECHANICAL SPECIFICATIONS (1) Front Side T-51512D121J-FW-A-AGN (AG) No. 2006-0045 OPTREX CORPORATION (Unit: mm) Page 14/35 ...
Page 15
... Rear Side プ [Note] We recommend you referring to the detailed drawing for your design. Please contact our company sales representative when you need the detailed drawing. T-51512D121J-FW-A-AGN (AG) No. 2006-0045 OPTREX CORPORATION (Unit:mm) Page 15/35 ...
Page 16
... Measurement method for luminance and Color Coordinates is as follows. TFT-LCD module The measuring method of the luminance is VESA standard it is being based on FLAT PANEL DISPLAY MEASUREMENTS STANDARD. T-51512D121J-FW-A-AGN (AG) No. 2006-0045 Ta=25°C, VCC=3.3V , Input Signals: Typ. Values shown in Section 6 SYMBOL CONDITION CR θ ...
Page 17
... Luminance Uniformity: point 1∼5 shown in a figure below *2) Definition of Contrast Ratio CR= Luminance with all white pixels / Luminance with all black pixels *3) Definition of Luminance Uniformity ∆Lw=[Lw(MAX)/Lw(MIN)-1] × 100 *4) Definition of Response Time Luminance *5) Definition of Viewing Angle(θ Left (-) LCD panel T-51512D121J-FW-A-AGN (AG) No. 2006-0045 200 400 ( 150 5 300 3 450 ...
Page 18
... Image sticking: Continuously display the test pattern shown in the figure below for two-hours. Then display a completely white screen. The previous image shall not persist more than two seconds at 25°C. Rows 298-302 T-51512D121J-FW-A-AGN (AG) No. 2006-0045 Cols 398-402 White Area TEST PATTERN FOR IMAGE STICKING TEST ...
Page 19
... The judgment of the above tests should be made as follow: Pass: Normal display image, no damage of the display function. (ex. no line defect) Partial transformation of the module parts should be ignored. Fail: No display image, damage of the display function. (ex. line defect) T-51512D121J-FW-A-AGN (AG) No. 2006-0045 40°C, 90%RH, 240 h BETWEEN −20°C (1h) and 80°C(1h), CONDITIONS ...