DMF-5010NF-FW-BE Optrex America Inc, DMF-5010NF-FW-BE Datasheet

Page 1

... I/O Terminal.......................................................................................................... 9 5. Test....................................................................................................................... 12 6. Appearance Standards..................................................................................... 13 7. Code System of Production Lot................................................................... 16 8. Type Number...................................................................................................... 16 9. Applying Precautions....................................................................................... 16 10. Precautions Relating Product Handling....................................................... 17 11. Warranty.............................................................................................................. 18 Rev. Date DMF5010NF-FW (AG) No.2000-0142 First Edition Apr 18, 2000 Final Revision ******* Table of Contents Revision History Page OPTREX CORPORATION OPTREX Approved by Production Div ...

Page 2

... Cold Cathode Fluorescent Lamp (CFL) × 1 Backlight ： Holder and PWB ground are connected by soldering. Additional Spec. CFL light unit is replaceable. ： Dimensional Outline Drawings DMF5010NF-FW (AG) No.2000-0142 * (W) × 66.0 (H) × 23.0 max. ( Without CFL Cable ( F-STN / Black &White-mode / Transmissive ) UE-32421C OPTREX CORPORATION ...

Page 3

... V IH Input Voltage Low Level V IL Input Voltage High Level V OH Output Voltage Low Level V OL Output Voltage I CC Supply Current I EE DMF5010NF-FW (AG) No.2000-0142 Conditions Min. − -0.3 − 0 − -0.3 Conditions Min. − 4.5 Shown in 3.1 =5.0V ± =5.0V ± 10% ...

Page 4

... Characteristics Parameter C/D Setup Time C/D Hold Time CE, RD, WR Pulse Width Data Setup Time Data Hold Time Access Time Output Hold Time C ∼ D7 (WRITE) D0 ∼ D7 (READ) DMF5010NF-FW (AG) No.2000-0142 Symbol Min. t 100 CDS t 10 CDH − ACC CDS ACC ...

Page 5

... Please maintain the above sequence when turning on and off the power supply of the module supplied to the module while internal alternate signal for LCD driving (M) is unstable or EE RESET is active, DC component will be supplied to the LCD panel. This may cause damage to the LCD module. DMF5010NF-FW (AG) No.2000-0142 0≦t 0 ≦ ≦ ≦ t T≧ ≧ ...

Page 6

... Average Life representes the time elapsed at the point of time when the residual ratio becomes below 50% when plural lamps are lighted in comparison with the definition of life mentioned above Recommended Inverter : HIU-32 ( Produced by HARISON ) CXA-L10L (DC 12.0V, Produced by TDK) DMF5010NF-FW (AG) No.2000-0142 Conditions Min. Typ. − − 270 − ...

Page 7

... Duty - 1/B Bias ( A : Duty Number Bias Number ). Driving voltage V the voltage V when the contrast ratio (CR=L O-P V O-P × 〈 ON SIGNAL 〉 DMF5010NF-FW (AG) No.2000-0142 Conditions Ta= 10 ℃ Ta=25 ℃ Ta=40 ℃ Ta=25 ℃ , 1/64 Duty, 1/9 Bias, V Conditions θ ﾟ , φ = −ﾟ ...

Page 8

... Driving condition : 1/64 Duty, 1/9 Bias ﾟ 135 ﾟ 180 ﾟ 225 ﾟ 270 ﾟ ･ Area shows typ. CR ≧ 2 3.4.System Block Diagram Photometer #1980A WB Computer DMF5010NF-FW (AG) No.2000-0142 f =13.3V, =70Hz ﾟ φ ( φ ﾟ） θ 180 ﾟ 315 ﾟ 270 ﾟ ...

Page 9

... CN2 No. Symbol 1 CFL (HOT CFL (GND) DMF5010NF-FW (AG) No.2000-0142 Level − Frame Ground ― Power Supply (0V, GND) ― Power Supply for Logic ― Power Supply for LCD Drive Write Signal L : Active Read Signal L : Active Chip Enable Signal L : Active Write Mode H : Command Write L : Data Write Read Mode H : Status Read L : Data Read − ...

Page 10

... It is recommended to apply a potentiometer for the contrast adjust due to the tolerance of the driving voltage and its temperature dependence 4.3.Block Diagram 8 D0 ∼ Control LSI CE T6963C C/D RESET FS X-tal 64K S-RAM VCC VSS J FG VEE CFL(HOT) CFL(GND) DMF5010NF-FW (AG) No.2000-0142 ∼ Ω Row Driver T6961B × equivalent Bias Circuit CFL Backlight ...

Page 11

... DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION OPTREX Page 11/18 ...

Page 12

... Note 4 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity after removed from the test chamber. Note 5 : Vibration test will be conducted to the product itself without putting container. DMF5010NF-FW (AG) No.2000-0142 Conditions 40 ℃± 2 ℃ , 96hrs (operation state) 10 ℃± 2 ℃ , 96hrs (operation state) 60 ℃ ...

Page 13

... All directions for inspecting the sample should be within 45 ﾟ against perpendicular line. 6.2.Definition of applicable Zones A Zone : Active display area B Zone : Area from outside of "A Zone" to validity viewing area C Zone : Rest parts A Zone + B Zone = Validity viewing area DMF5010NF-FW (AG) No.2000-0142 45 ﾟ A Zone Bezel Flame B Zone C Zone ...

Page 14

... Black and (1) Round Shape White Spots, Foreign Substances (2) Line Shape Total defects shall not exceed 5. 2 Air Bubbles (between glass & polarizer) Total defects shall not exceed 3. DMF5010NF-FW (AG) No.2000-0142 Criteria Zone Dimension (mm ≦ 0.1 * 0.1 ＜ D ≦ 0.2 3 0.2 ＜ D ≦ 0.25 2 0.25 ＜ ...

Page 15

... Black spots, line shaped foreign substances or air bubbles between Substance Defects glass & polarizer should be 5pcs maximum in total. D ≦ 0.2 : 20mm or more 7 Distance between 0.2 ＜ 40mm or more Different Foreign Substance Defects DMF5010NF-FW (AG) No.2000-0142 Criteria 0.15 ≧ OPTREX CORPORATION OPTREX As per the sketch of left hand. ...

Page 16

... The type number of module is specified on the back of module as follows. ＤＭＦ５０１０ ＮＦ−ＦＷ Etching or Printing 9.Applying Precautions Please contact us when questions and/or new problems not specified in this specifications arise. DMF5010NF-FW (AG) No.2000-0142 □ □ Factory Number (Numeral) Factory Code (Alphabet) Production Week (1 ∼ ...

Page 17

... Care should be taken not to touch connection areas to avoid burns. ② Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn. ③ The use of CFLs for extended periods of time at low temperatures will significantly shorten their service life. DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION OPTREX Page 17/18 ...

Page 18

... Optrex will not be held responsible for any quality guarantee issue for defect products judged as Optrex-origin longer than 2 (two) years from Optrex production or 1(one) year from Optrex, Optrex America, Optrex Europe, Display LC delivery which ever comes later. DMF5010NF-FW (AG) No.2000-0142 OPTREX CORPORATION OPTREX ...