4167201-XX Digital View Inc, 4167201-XX Datasheet - Page 4

• Manufacturer Part Number: 4167201-XX
• Description: CTRLR ACG-1024 FOR SVGA PANELS
• Manufacturer: Digital View Inc

Specifications of 4167201-XX

• Voltage - Input: 12V
• Voltage - Output: 3.3V, 5V, 12V
• Size / Dimension: 4.2" L x 3.6" W (107mm x 92mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 586-1005

IMPORTANT: Please read the Application Notes section for more information.
CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious
damage.
CONNECTION
Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
The red LED will light up when power on with the presence of input signal. The LED will change to green.
General:
in this manual, “Connector, Pinouts & Jumpers” to ensure the correct pin to pin wiring.
PC SETTINGS
The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics performance
we recommend choosing 60Hz vertical refresh rate – this will not cause screen flicker.
OPERATION
Once the system has been connected and switched on there are a number of functions available to adjust the display
image as summarized in the following sections. The settings chosen will be saved for each mode independently.
CONNECTION & OPERATION
Controller Mounting: It is recommended that a clearance of at least 10mm is provided above and 5mm below the
controller when mounted. Additionally consideration should be given to:
PC Graphics Output: A few guidelines:
If you are using supplied cables & connectors, ensure they are correct for the model of panel and controller.
If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section
Electrical insulation
Grounding.
EMI shielding.
Cable management. Note: It is important to keep panel signal cables apart from the inverter & backlight cables to
prevent signal interface.
Heat & ventilation: Heat generated from other sources, for example the backlight of a very high brightness panel may
generate significant heat which could adversely affect the controller.
Other issues that may affect safety or performance.
Signal quality is very important, if there is noise or instability in the PC graphics output this may result in visible noise
on the display.
Vertical refresh rate should be set to 60Hz preferable.
Non-interlaced is required.
LCD panel & Inverter: Connect the inverter (if it is not built-in the panel) to the CCFT lead connector of the LCD
panel.
TTL type panels: Plug the signal cables direct to CN2, CN3 and CN4 (necessary for 8-bit panel only) on the
controller board. Plug the other end of cables to the LCD connector board (if connector board is required, otherwise
the signal can be direct plug to the LCD panel connector). Then plug the board connector to the LCD panel
connector.
LVDS/PanelLink type panels: A LVDS/PanelLink transmitter board is required. Plug the transmitter board to CN2,
CN3 and CN4 (necessary for 8-bit panel only). Then insert the LCD signal cable with controller end to the connector
on the transmitter board. Insert the panel end of the cable the LCD panel connector.
Inverter & Controller: Plug the inverter cable to CNB1 and CNA1 (if necessary). Plug another end to the connector
on the inverter.
Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another to the
OSD switch mount.
LED & Controller: Plug in a 3-way with dual colour LED to connector LED1 on the controller board.
Jumpers : Check all jumpers are set correctly. Details referring the connection diagram (a separate document) or
the jumpers setting table (in the following section).
Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JB2, JB3, JA5. JB2 & JB3
are used for inverter control (read inverter specification and information on the jumper table to define the correct
settings). JA3 & JA5 are used for panel voltage input (read panel specification and information on the jumper table to
define the correct settings).
VGA cable & Controller: Plug the VGA cable to the connector P1 on the controller board.
Power supply & Controller: Plug the DC 12V power in to the connector PP1.
Power on: Switch on the controller board and panel by using the OSD switch mount.
Page 4