HFBR-5963LZ Avago Technologies US Inc., HFBR-5963LZ Datasheet - Page 3

• Manufacturer Part Number: HFBR-5963LZ
• Description: TXRX MMF FE ATM SONET OC-3 2X5
• Manufacturer: Avago Technologies US Inc.

Specifications of HFBR-5963LZ

• Applications: Ethernet
• Data Rate: 155MBd
• Wavelength: 1300nm
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Mounting Type: Through Hole
• Supply Voltage: 3.3V
• Wavelength Typ: 1300nm
• Leaded Process Compatible: Yes
• Optical Fiber Type: TX/RX
• Optical Rise Time: 3/2.2ns
• Optical Fall Time: 3/2.2ns
• Jitter: 0.4/0.3ns
• Operating Temperature Classification: Commercial
• Peak Wavelength: 1308/1380nm
• Package Type: DIP With Connector
• Operating Supply Voltage (min): 2.97V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.63V
• Output Current: 50mA
• Operating Temp Range: 0C to 70C
• Mounting: Snap Fit To Panel
• Pin Count: 10
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Figure 2. Pin Out Diagram
Pin Descriptions:
Pin 1 Receiver Signal Ground V
Directly connect this pin to the receiver ground plane.
Pin 2 Receiver Power Supply Vcc RX
Provide +3.3 V dc via the recommended receiver power
supply filter circuit. Locate the power supply filter circuit
as close as possible to the V
Pin 3 Signal Detect SD
Normal optical input levels to the receiver result in a logic
“1” output.
Low optical input levels to the receiver result in a logic “0”
output.
This Signal Detect output can be used to drive a +3.3 V TTL
input on an upstream circuit, such as Signal Detect input
or Loss of Signal-bar.
Pin 4 Receiver Data Out Bar RD-
No internal terminations are provided. See recommended
circuit schematic.
Pin 5 Receiver Data Out RD+
No internal terminations are provided. See recommended
circuit schematic.
Pin 6 Transmitter Power Supply V
Provide +3.3 V dc via the recommended transmitter power
supply filter circuit.
Locate the power supply filter circuit as close as possible
to the V
3
RECEIVER SIGNAL GROUND
RECEIVER POWER SUPPLY
RECEIVER DATA OUT BAR
RECEIVER DATA OUT
SIGNAL DETECT
CC
TX pin.
o
o
o
o
o
RX
1
2
3
4
5
View
Top
EE
10
TX
9
8
7
6
CC
RX
o
o
o
o
o
CC
RX pin.
TX
TRANSMITTER DATA IN BAR
TRANSMITTER DATA IN
NC
TRANSMITTER SIGNAL GROUND
TRANSMITTER POWER SUPPLY
Studs/Solder
Mounting
Posts
Pin 7 Transmitter Signal Ground V
Directly connect this pin to the transmitter ground plane.
Pin 8 NC
No connection.
Pin 9 Transmitter Data In TD+
No internal terminations are provided. See recommended
circuit schematic.
Pin 10 Transmitter Data In Bar TD-
No internal terminations are provided. See recommended
circuit schematic.
Mounting Studs/Solder Posts
The mounting studs are provided for transceiver mechani-
cal attachment to the circuit board.
It is recommended that the holes in the circuit board be
connected to chassis ground.
Application Information
The Applications Engineering group is available to assist
you with the technical understanding and design trade-
offs associated with these transceivers. You can contact
them through your Avago sales representative.
The following information is provided to answer some
of the most common questions about the use of these
parts.
Transceiver Optical Power Budget versus Link Length
Optical Power Budget (OPB) is the available optical power
for a fiber optic link to accommodate fiber cable losses plus
losses due to in-line connectors, splices, optical switches,
and to provide margin for link aging and unplanned losses
due to cable plant reconfiguration or repair.
Avago LED technology has produced 1300 nm LED
devices with lower aging characteristics than normally
associated with these technologies in the industry. The
industry convention is 1.5 dB aging for 1300 nm LEDs. The
1300 nm Avago LEDs are specified to experience less than
1 dB of aging over normal commercial equipment mission
life periods.
Contact your Avago sales representative for additional
details.
EE
TX