HFBR-5961ALZ Avago Technologies US Inc., HFBR-5961ALZ Datasheet
HFBR-5961ALZ
Specifications of HFBR-5961ALZ
Available stocks
Related parts for HFBR-5961ALZ
HFBR-5961ALZ Summary of contents
Page 1
... Full compliance with the optical performance require- ments of the FDDI PMD standard • Full compliance with the optical performance require- ments of 100Base-FX version of IEEE802.3u • RoHS compliant • PECL Signal Detect Output • Temperature range: HFBR-5961LZ 0 °C to +70 °C HFBR-5961ALZ -40 °C to +85 °C HFBR-5961GZ 0 °C to +70°C (No EMI shield) HFBR-5961AGZ -40 °C to +85°C (No EMI shield) Applications • SONET/SDH equipment interconnect, OC-3/SDH STM-1 rate • Fast Ethernet ...
Page 2
Package The overall package concept for the Avago transceiver consists of three basic elements; the two optical subas- semblies, an electrical subassembly, and the housing as illustrated in the block diagram in Figure 1. The package outline drawing and pin out are shown in Figures 2 and 5. The details of this package outline and pin out are compliant with the multisource definition of the DIP. The low profile of the Avago transceiver design complies with the maximum height allowed for the LC connector over the entire length of the package. The optical subassemblies utilize a high-volume assembly process together with low-cost lens elements which result in a cost effective building block. The electrical subassembly consists of a high volume multilayer printed circuit board ...
Page 3
RX TX Top View o RECEIVER SIGNAL GROUND RECEIVER POWER SUPPLY SIGNAL DETECT RECEIVER DATA OUT BAR RECEIVER DATA OUT Figure ...
Page 4
... Recommended Handing Precautions Avago recommends that normal status precautions be taken in the handling and assembly of these transceiv- ers to prevent damage which may be induced by elec- trostatic discharge (ESD). The HFBR-5961xxZ series of transceivers meet MIL-STD-883C Method 3015.4 Class 2 products. Care should be used to avoid shorting the receiver data or signal detect outputs directly to ground without proper current limiting impedance. Solder and Wash Process Compatibility The transceivers are delivered with protective process plugs inserted into the LC receptacle ...
Page 5
Board Layout - Hole Pattern The Avago transceiver complies with the circuit board “Common Transceiver Footprint” hole pattern defined in the original multisource announcement which defined the package style. This drawing is reproduced in Figure 6 with the addition of ANSI Y14.5M compliant dimensioning to be used as a guide in the ...
Page 6
ALL DIMENSIONS IN MILIMETERS(INCHES) Figure 5. Package Outline Drawing 6 ...
Page 7
... THIS PAGE DESCRIBES THE RECOMMENDED CIRCUIT BOARD LAYOUT AND FRONT PANEL OPENINGS FOR SFF TRANSCEIVERS. 2. THE HATCHED AREAS ARE KEEP-OUT AREAS RESERVED FOR HOUSING STANDOFFS. NO METAL TRACES ALLOWED IN KEEP-OUT AREAS. 3. THIS DRAWING SHOWS EXTRA PIN HOLES FOR PIN AND PIN TRANSCEIVERS. THESE EXTRA HOLES ARE NOT REQUIRED FOR HFBR-5961xxZ AND OTHER PIN SFF MODULES. 4. HOLES FOR MOUNTING STUDS MUST NOT BE TIED TO SIGNAL GROUND BUT MAY BE TIED TO CHASSIS GROUND. 5. HOLES FOR HOUSING LEADS OPTIONAL AND NOT REQUIRED FOR HFBR-5961L/HFBR-5961G. IF NEEDED IN FUTURE, THESE HOLES MUST BE TIED TO SIGNAL GROUND. 6. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). Figure 6. Recommended Board Layout Hole Pattern 7 ...
Page 8
... Typically show no measurable effect from a 10 V/m field swept from 80 to 450 MHz applied to the transceiver when mounted to a circuit card withouta chassis enclosure. Compliant per Avago testing under single fault conditions. TUV Certification - R 02071015 UL File #: E173874 HFBR-5961xxZ TRANS- MITTER TEST RESULTS OF λ ∆λ AND t r/f ARE CORRELATED AND COMPLY WITH THE ALLOWED SPECTRAL WIDTH AS A FUNCTION OF CENTER WAVELENGTH FOR VARIOUS RISE AND FALL TIMES ...
Page 9
... Differential Input Voltage (p-p) Output Current Recommended Operating Conditions Parameter Case Operating Temperature HFBR-5961LZ/GZ HFBR-5961ALZ/AGZ Supply Voltage Data Input Voltage - Low Data Input Voltage - High Data and Signal Detect Output Load Differential Input Voltage (p-p) Transmitter Electrical Characteristics HFBR-5961LZ/ °C to +70 ° HFBR-5961ALZ/AGZ (T = -40 °C to +85 ° Parameter Supply Current Power Dissipation Data Input Current - Low Data Input Current - High 9 Symbol Minimum Typical T - SOLD ...
Page 10
... Data Output Voltage - Low Data Output Voltage - High Data Output Rise Time Data Output Fall Time Signal Detect Output Voltage - Low Signal Detect Output Voltage - High Signal Detect Output Rise Time Signal Detect Output Fall Time Power Supply Noise Rejection Transmitter Optical Characteristics HFBR-5961LZ/ °C to +70 ° HFBR-5961ALZ/AGZ (T = -40 °C to +85 ° Parameter Output Optical Power BOL62.5/125 µ 0.275 Fiber EOL Output Optical Power BOL50/125 µ 0.20 Fiber EOL Optical Extinction Ratio Output Optical Power at Logic Low 0 State Center Wavelength ...
Page 11
... Receiver Optical and Electrical Characteristics HFBR-5961LZ/ °C to +70 ° HFBR-5961ALZ/AGZ (T = -40 °C to +85 ° Parameter Input Optical Power at minimum at Window Edge OC-3 FE Input Optical Power at Eye Center OC-3 FE Input Optical Power Maximum OC-3 FE Operating Wavelength Systematic Jitter Contributed by the Receiver OC-3 Duty Cycle Distortion Contributed by the Receiver FE Data Dependent Jitter Contributed by the Receiver FE Random Jitter Contributed by the Receiver OC-3 FE Signal Detect - Asserted OC-3 FE Signal Detect - Deasserted Signal Detect - Hysteresis ...
Page 12
... At the Beginning of Life (BOL) over the specified operating temperature and voltage ranges 23 input is a 155.52 MBd PRBS data pattern with 72 “1” s and 72 “0”s inserted per the CCITT (now ITU-T) recommendation G.958 Appendix I. Receiver data window time-width is 1. greater for the clock recovery circuit to operate in. The actual test data window time-width is set to simulate the effect of worst case optical input jitter based on the transmitter jitter values from the specification tables. The test window time-width is HFBR-5961L 3.32 ns. Transmitter operating with a 155.52 MBd, 77.5 MHz square-wave, input signal to simulate any cross-talk present between the transmitter and receiver sections of the transceiver. 15b. T his specification is intended to indicate the performance of the receiver section of the transceiver when Input Optical Power signal char- acteristics are present per the following definitions ...
Page 13
... LED (Operating Case Temperature 0 to +70 °C) HFBR-5961LZ/HFBR-5961GZ 1300 nm LED (Operating Case Temperature -40 to +85 °C) HFBR-5961ALZ/HFBR-5961AGZ For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States and other countries. ...