HFCT-711XPD Avago Technologies US Inc., HFCT-711XPD Datasheet
HFCT-711XPD
Specifications of HFCT-711XPD
Related parts for HFCT-711XPD
HFCT-711XPD Summary of contents
Page 1
... HFCT-711XPD Multi-rate 1310 nm XFP 10 Gbit/s Optical Transceiver Data Sheet Description The 1310 nm XFP transceiver is a high performance, cost effective module for serial optical data communications applications specified for signal rates of 9.95 Gb/s to 10.5 Gb/ compliant to XFP MSA Rev 4.5. The module is designed for single mode fiber and operates at a nominal wavelength of 1310 nm ...
Page 2
... Installation The HFCT-711XPD is hot-pluggable, allowing the module to be installed while the host system is operating and on-line. The attach heatsink is designed to clip on to the XFP cage without a module present. ...
Page 3
... RX_LOS can also be monitored via the two- wire serial interface (byte 110, bit 1). Functional Data I/O Avago Technologies’ HFCT-711XPD fiber-optic transceiver is designed to accept industry standard electrical input differential signals. The transceiver provides ac-coupled, internally terminated data input and output interfaces. ...
Page 4
Table 1. Electrical Pin Definitions Pin Name Logic 1 GND Mod-Desel LVTTL-I 4 Interrupt LVTTL-O 5 TX_DIS LVTTL GND SCL LVTTL-I ...
Page 5
Absolute Maximum Ratings Parameter Storage Temperature (non-operating) Ambient Operating Temperature Relative Humidity Supply Voltage Low Speed Input Voltage Recommended Operating Conditions Parameter Case Operating Temperature Supply Voltage Data Rate Transceiver Electrical Characteristics ( °C to +70 °C, V ...
Page 6
Transmitter Electrical Input Characteristics ( °C to +70 ° 3.3 V ± 5 Parameter Differential Input Impedance Termination Mismatch Differential Input Amplitude Differential Input Return Loss Differential Input Return Loss Differential Input Return ...
Page 7
Transmitter Optical Characteristics 10 GbE/10GFC ( °C to +70 ° 3.3 V ± 5 Parameter Optical Output Power Average Optical Output Power Extinction Ratio Spectral Width - rms Center Wavelength Transmitter and dispersion ...
Page 8
Transmitter Optical Characteristics OC-192 SONET SR °C to +70 ° 3.3 V ± 5 Parameter Optical Output Power Extinction Ratio Spectral Width @ 20 dB Center Wavelength Side mode suppression ratio Output ...
Page 9
Transceiver Timing Characteristics ( °C to +70 ° 3.3 V ± 5 Parameter Symbol TX_DIS Assert Time t_off TX_DIS Negate Time t_on Time to initialize t_init Interrupt assert delay Interrupt_on Interrupt negate delay ...
Page 10
... The HFCT-711XPD uses a closed loop laser bias feedback circuit to maintain constant optical power and extinction ratio. This circuit compensates for normal laser parametric variations in quantum efficiency, forward voltage and lasing threshold due to changing transceiver operating points ...
Page 11
Mechanical Specifications Package Dimensions Figure 6a. Module Drawing Figure 6b. Module Drawing 11 ...
Page 12
Figure 7. XFP host board mechanical layout 12 ...
Page 13
... Application Support An Evaluation Kit and Reference Designs are available to assist in evaluation of the HFCT-711XPD. Please contact your local Field Sales representative for availability and ordering details. Regulatory Compliance The transceiver Regulatory Compliance performance is provided in Table figure of merit to assist the designer. The overall equipment design will determine the certification level ...
Page 14
... IR reflow or wave soldering processes. Caution The HFCT-711XPD contains no user serviceable parts. Tampering with or modifying the performance of the HFCT-711XPD will result in voided product warranty. It may also result in improper operation of the HFCT- 711XPD circuitry, and possible overstress of the laser source. Device degradation or product failure may result. ...