LXMG1813-12-62S Microsemi Analog Mixed Signal Group, LXMG1813-12-62S Datasheet - Page 3

• Manufacturer Part Number: LXMG1813-12-62S
• Description: MOD INVERTER CCFL 6W 12V PROG
• Manufacturer: Microsemi Analog Mixed Signal Group
• Series: PanelMatch™r
• Type: Inverters for CCFL and UV Lampsr

Specifications of LXMG1813-12-62S

• Voltage - Input: 12V
• Output: 1600V
• Size / Dimension: 4.33" L x 0.63" W x 0.24" H (110mm x 16mm x 6mm)
• Mounting Type: Chassis Mount
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Copyright © 2008
Rev 1.0, 2008-11-14
CN1 (Molex 53261-0871 or equivalent) mates with 51021-0800 housing, 50079-8100 pins. Mates with LX9501G input cable assembly
CN2 (Molex 53261-0371 or equivalent) mates with 51021-0800 housing, 50079-8100 pins. Mates with LXMG1800_LS ALS Assembly
The following specifications apply over the recommended operating condition and ambient temperature of 0°C to 60°C except where
otherwise noted; ALS_IN ≥ 2.3V,
BRITE INPUT
SLEEP BAR INPUT
RUN Mode
SLEEP Mode
SET
SET
Input Current
ALS (AMBIENT LIGHT SENSOR)
ALS_VCC
POWER CHARACTERISTICS
Sleep Current
Run Current
Strike (Open Lamp)
Supply Current under Fault condition
Typical Efficiency
Potentiometer Max Impedance
Potentiometer Min Impedance
C
CN1-1
CN1-2
CN1-3
CN1-4
CN1-5
CN1-6
CN1-7
CN1-8
CN2-1
CN2-2
CN2-3
ONN
1,2
1,2
TM
INPUT
Low Threshold
Parameter
11861 Western Avenue, Garden Grove, CA. 92841, 800-877-6458, 714-898-8121, Fax: [phone]
ASL_GND
ALS_VCC
SLEEP
ALS_IN
BRITE
GND
SET
SET
P
V
IN
IN
1
2
E L E C T R I C A L C H A R A C T E R I S T I C S ( C O N T I N U E D )
Main Input Power Supply (9V ≤ V
Power Supply Return
ON/OFF Control. (0V ≤
Can be left open or connected to a 500k potentiometer to reduce brightness when the LXMG1800_LS is
connected to CN3. Not recommended as brightness control voltage input.
SET
SET
Nominal 5.1V Supply for ALS Board Assembly. 3mA maximum output load
Brightness Control Voltage input from light sensor board.
ALS Board Power Supply Return.
SLEEP
1
2
MSB Connecting this pin to ground decreases the output current (see Table 1)
LSB Connecting this pin to ground decreases the output current (see Table 1)
Symbol
T
BRT
F U N C T I O N A L P I N D E S C R I P T I O N
≥ 2.0V, VIN = 12V.
V
V
ALS
I
S_DWELL
I
IN(MIN)
FAULT
I
I
SLEEP
SLEEP
V
RUN
SET
η
L
POT
VCC
Analog Mixed Signal Group
Full Lamp Current
Minimum Lamp Current
V
I
SET
Fault condition
SET
SLEEP ≤ 0.8V
LOAD
SETx
®
Microsemi
1
1
SLEEP
= 3mA
= 0V
= Open SET
= Open SET
PanelMatch™ VEasyLIT™ LXMG1813-12-6xS
IN
≤ 0.8V = OFF,
Test Conditions
≤ 16.8V)
2
2
= Ground, V
= Ground, V
12V 6W CCFL Programmable Inverter Module
D
SLEEP
ESCRIPTION
LAMP
LAMP
P
RODUCTION
= 590V
= 590V
≥ 2.0V = ON
RMS
RMS
D
ATASHEET
Min
-475
-0.3
400
2.0
1.5
LXMG1813-12-6xS
75
4.8
Typ
-510
500
370
10
80
5.1
0
0
2
8
Max
-555
0.8
2.5
V
20
5.5
IN
Units
Sec
mA
mA
kΩ
kΩ
µA
µA
Page 3
%
V
V
V
V