PVG5H101A01R00 Murata Electronics North America, PVG5H101A01R00 Datasheet - Page 5

• Manufacturer Part Number: PVG5H101A01R00
• Description: POT 100 OHM TRIM 11TRN SIDE SMD
• Manufacturer: Murata Electronics North America
• Series: PVG5r

Specifications of PVG5H101A01R00

• Resistance (ohms): 100
• Power (watts): 0.25W, 1/4W
• Taper: Linear
• Tolerance: ±10%
• Temperature Coefficient: ±150ppm/°C
• Number Of Turns: 11
• Adjustment Type: Side Adjustment
• Mounting Type: Surface Mount
• Resistive Material: Cermet
• Package / Case: Square - 0.193" L x 0.189" W x 0.146" H (4.90mm x 4.80mm x 3.70mm)
• Resistance In Ohms: 100
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 490-2224-2

!Note
!Note
1. Store that the temperature is -10 to +40deg. C and
2. Do not store in or near corrosive gases.
3. Use within six months after delivery.
4. Open the package just before using.
5. Do not store under direct sunlight.
6. The trimmer potentiometer should not be used under
1. When using with partial load (rheostat), minimize
2. The maximum input voltage to a trimmer
3. The maximum input current to a trimmer
1. Soldering
2. Mounting
(1) Standard soldering condition
(2) Can not be soldered using the flow soldering
(3) The soldering iron should not come in contact
(4) Insufficient amounts of solder can lead to
(1) Use our standard land dimension. Excessive land
Notice (Operating and Storage Conditions)
the relative humidity is 30-85%RH.
the following environmental conditions:
If you use the trimmer potentiometer in an
environment other these listed below, please
consult with Murata factory representative prior to
Notice (Rating)
the power depend on the resistance value.
potentiometer should not exceed (P•R)^1/2 or the
maximum operating voltage, whichever is smaller.
potentiometer should not exceed (P/R)^1/2 or the
allowable wiper current, whichever is smaller.
Notice (Soldering and Mounting)
(a) Reflow and flow soldering :
(b) Soldering iron :
Before using other soldering conditions than
those listed above, please consult with Murata
factory representative prior to using. If the
soldering conditions are not suitable, e. g.,
excessive time and/or excessive temperature,
the trimmer capacitor may deviate from the
specified characteristics.
method. If you use the flow soldering method,
the trimmer potentiometer may not function.
with the case of the trimmer potentiometer. If
such contact does occur, the trimmer
potentiometer may be damaged.
insufficient soldering strength on PCB.
Excessive amounts of solder may cause the
bridging between the terminals.
area causes displacement due to effect of the
• Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specification or transact the approval sheet for product specification before ordering.
Please read rating and !CAUTION (for storage and operating, rating, soldering and mounting, handling) in this PDF catalog to prevent smoking and/or burning, etc.
This catalog has only typical specifications. Therefore, you are requested to approve our product specification or to transact the approval sheet for product specificaion before ordering.
Refer to the standard temperature profile.
>Temperature of tip 260 deg.C max.
>Soldering time
>Diameter
>Wattage of iron
3sec. max.
30W max.
2mm dia. max.
3. Cleaning
(1) Corrosive gaseous atmosphere.
(2) In liquid.
(3) Dusty/dirty atmosphere.
(4) Direct sunlight.
(5) Static voltage nor electric/magnetic fields.
(6) Direct sea breeze.
(7) Other variations of the above.
(2) Do not apply excessive force (preferable 9.8N
(3) Do not warp and/or bend PC board to prevent
(4) In chip placers, the recommended size of the
(1) Isopropyl-alcohol and Ethyl-alcohol are
(2) The total cleaning time by cold dipping, vaper
(3) For ultra-sonic cleaning, the available
using.
condition is as follows.
(Ex. Chlorine gas, Hydrogen sulfide gas, Ammonia
gas, Sulfuric acid gas, Nitric oxie gas, etc.)
(Ex. Oil, Medical liquid, Organic solvent, etc.)
surface tension of the solder. Insufficient land
area leads to insufficient soldering strength of
the chip.
(Ref.; 1kgf) max.), when the trimmer potentiometer
is mounted to the PCB.
trimmer potentiometer from breakage.
cylindrical pick-up nozzle should be outer
dimension 4.0mm dia. and inner dimension 2.0mm
dia..
applicable solvent for cleaning. If you use any
other types of solvents, please consult with
Murata factory representative prior to using.
and ultrasonic washing (conditions as below)
method shall be less than 3 minutes.
Due to the ultra-sonic cleaning equipment
peculiar self resonance point and the cleaning
compatibility usually depends on the jig
construction and/or the cleaning condition such
as the depth of immersion, please check the
>Power
>Frequency
>Temperature : Ambient temperature
: 28kHz
: 600W (67liter) max.
PVG5/PV01 Series Notice
Continued on the following page.
R50E12.pdf 02.9.5
37
6