MPD6D104S Murata Electronics North America, MPD6D104S Datasheet - Page 8

• Manufacturer Part Number: MPD6D104S
• Description: CONV DC/DC 10W 1.8VOUT 3A SMT
• Manufacturer: Murata Electronics North America
• Series: MPDr
• Type: Isolatedr

Specifications of MPD6D104S

• Output: 1.8V
• Number Of Outputs: 1
• Power (watts): 10W
• Mounting Type: Surface Mount
• Voltage - Input: 36 ~ 75V
• Package / Case: 18-DIP SMD Module (15 Leads)
• 1st Output: 1.8 VDC @ 3A
• Size / Dimension: 1.47" L x 0.88" W x 0.17" H (37.3mm x 22.4mm x 4.2mm)
• Power (watts) - Rated: 10W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 86%
• Approvals: CE, cUL, UL, TUV
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -
• 4th Output: -
• Other names: 490-4585

1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’ s specifications are subject to change or our
2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product
Note:
products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering.
specifications or transact the approval sheet for product specifications before ordering.
9.2.2. Over Voltage Protection (OVP)
9.2.3. Low Voltage Protection (LVP)
9.2.4. Remote On/Off Control
9.2.5. Alarm Output (ALM)
The Isolated DC-DC Converter become into latch-up mode after typical 0.5ms. mask time,when the
output voltage is over the value specified in Over Voltage Protection(9.1.2) by failure of internal
control circuit. In order to reset, the input voltage is set under 5V for 1s. min. Output voltage might
exceed the point at which OVP starts to function under the specific condition of transient input
voltage or output current change. Therefore,OVP is set to wait for the mask time 0.5ms. It is
recommended to evaluate your appliances installed with the DC-DC Converter.
The Isolated DC-DC Converter becomes into latch-up mode after typical 500ms. mask time,when
the output voltage is under the value specified in Low Voltage
Protection(9.1.2) by operating Over Current-limit Inception due to failure of internal control or over
load. In order to reset, the input voltage is set under 5V for 1s. min.
The connection to a RC pin controls an Isolated DC-DC Converter to turn on/off.
While the Isolated DC-DC Converter is halted under the remote control, alarm function does not
operate;refer to Alarm Output.
The Alarm Output can be down to the level of -Vin (Open Drain Output), when Over Voltage
Protection or Low Voltage Protection operates. Sink current in ALM pin is 10mA max. The Isolated
DC-DC Converter running for multiple and/or parallel operation are enable to simultaneously halt by
connecting all ALM pins, in the case of Over Voltage Protection or Low Voltage Protection caused
by any single DC-DC Converter.
To connect more than 10,please consult Murata.
Start
Halt
Reset Condition
Reset Condition
: RC is open or connected to -Vin
: RC is connected to +Vin
Vin 36 to 75V
Vin 36 to 75V
5V min
5V min
Maximum number running DC-DC Converters is 10pcs.
1s.min
1s.min
MPD6D10*S Specification
2010.5.7
8