LTM4601AIV-1#PBF Linear Technology, LTM4601AIV-1#PBF Datasheet - Page 13

• Manufacturer Part Number: LTM4601AIV-1#PBF
• Description: IC DC/DC UMODULE 12A 133-LGA
• Manufacturer: Linear Technology
• Series: µModuler
• Type: Point of Load (POL) Non-Isolatedr

Specifications of LTM4601AIV-1#PBF

• Design Resources: LTM4601A-1 Spice Model
• Output: 0.6 ~ 5 V
• Number Of Outputs: 1
• Power (watts): 60W
• Mounting Type: Surface Mount
• Voltage - Input: 4.5 ~ 20V
• Package / Case: 133-LGA
• 1st Output: 0.6 ~ 5 VDC @ 12A
• Size / Dimension: 0.59" L x 0.59" W x 0.11" H (15mm x 15mm x 2.8mm)
• Power (watts) - Rated: 60W
• Operating Temperature: -40°C ~ 85°C
• Efficiency: 95%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• 3rd Output: -
• 2nd Output: -

APPLICATIONS INFORMATION
is frequency and m is the number of parallel phases. This
calculation process can be easily fulfi lled using our Linear
Technology μModule Design Tool.
Fault Conditions: Current Limit and Overcurrent
Foldback
LTM4601A has a current mode controller, which inher-
ently limits the cycle-by-cycle inductor current not only
in steady-state operation, but also in transient.
To further limit current in the event of an overload condition,
the LTM4601A provides foldback current limiting. If the
output voltage falls by more than 50%, then the maximum
output current is progressively lowered to about one sixth
of its full current limit value.
Soft-Start and Tracking
The TRACK/SS pin provides a means to either soft-start
the regulator or track it to a different power supply. A
capacitor on this pin will program the ramp rate of the
output voltage. A 1.5μA current source will charge up the
external soft-start capacitor to 80% of the 0.6V internal
voltage reference minus any margin delta. This will control
the ramp of the internal reference and the output voltage.
The total soft-start time can be calculated as:
When the RUN pin falls below 1.5V, then the SS pin is reset
to allow for proper soft-start control when the regulator
is enabled again. Current foldback and force continuous
mode are disabled during the soft-start process. The
soft-start function can also be used to control the output
ramp up time, so that another regulator can be easily
tracked to it.
Output Voltage Tracking
Output voltage tracking can be programmed externally
using the TRACK/SS pin. The output can be tracked up and
t
SOFTSTART
0.8 • 0.6V – V
OUT(MARGIN)
•
1.5μA
C
SS
V
down with another regulator. The master regulator’s output
is divided down with an external resistor divider that is the
same as the slave regulator’s feedback divider. Figure 5
shows an example of coincident tracking. Ratiometric
modes of tracking can be achieved by selecting different
resistor values to change the output tracking ratio. The
master output must be greater than the slave output for
the tracking to work. Figure 6 shows the coincident output
tracking characteristics.
C
IN
IN
Figure 6. Coincident Output Tracking Characteristics
100k
LTM4601A/LTM4601A-1
VOLTAGE
OUTPUT
PGOOD
MPGM
RUN
COMP
INTV
DRV
CC
CC
SGND
Figure 5. Coincident Tracking
V
IN
LTM4601A
PLLIN
PGND
TRACK/SS
f
V
DIFFV
SET
OUT_LCL
TRACK CONTROL
MARG0
MARG1
V
V
TIME
OSNS
OSNS
V
OUT
OUT
V
FB
+
–
MASTER OUTPUT
SLAVE OUTPUT
4601A F05
R
40.2k
SET
4601A F06
MASTER
OUTPUT
SLAVE OUTPUT
C
OUT
R2
60.4k
R1
40.2k
13
4601afb