EK06 Cirrus Logic Inc, EK06 Datasheet

EK06

Manufacturer Part Number

EK06

Description

EVALUATION KIT FOR SA60

Manufacturer

Cirrus Logic Inc

Series

Apex Precision Power™r

Datasheet

1.EK06.pdf (3 pages)

Specifications of EK06

Main Purpose

Power Management, H Bridge Driver (Internal FET)

Embedded

Utilized Ic / Part

SA60

Primary Attributes

10 V ~ 80 V Supply, 10A Output

Secondary Attributes

Assembly Required

Product

Amplifier Modules

Description/function

Audio Amplifiers

For Use With/related Products

SA60

Lead Free Status / RoHS Status

Contains lead / RoHS non-compliant

Other names

598-1388

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

EK06

Manufacturer:

SANKEN

Quantity:

2 000

Company:

Meier Automation Equipment Co., Limited

Part Number:

EK06

Manufacturer:

VISHAY/威世

Quantity:

20 000

Company:

Meier Automation Equipment Co., Limited

Part Number:

EK06V1

Manufacturer:

VISHAY/威世

Quantity:

20 000

Current page: 1 of 3
Download datasheet (278Kb)

INTRODUCTION

possible with the EK06 evaluation kit. The amplifier may be

mounted vertically with the HS20 heat sink, or horizontally.

Connections are provided for required power supply bypassing

recommended protection components, as well as optional current

sense resistors. A large area for component mounting provides

flexibility and makes a multitude of circuit configurations possible.

ASSEMBLY

1. On the silk screen side of the evaluation board, insert and

2. Solder components for your circuit. Be sure to include proper

3. Place the TW07 thermal washer on the heat sink over the

FIGURE 1.

EK06U

CAUTION

Fast and easy breadborading of circuits using the SA60 are

solder the MS06 mating socket in DUT holes 1 – 12. Be sure

each one is fully seated.

bypassing. See the SA60 data sheet for help in selecting

these components. 1uF capacitors and a .10Ω resistor have

been included with the EK06 kit but may be replaced with

other components as necessary. C1, not provided, should

be selected for the voltage required by the application. See

Apex Precision Power Application Note 30 for guidelines in

selecting this bypass capacitor. If current sense resistors are

not used, the I SENSE traces on the EVAL11 board must be

shorted to power ground in place of the resistors.

mounting hole for the DUT. Place a #6 screw through the

mounting hole and thread a #6 nut onto the screw at the back

of the heat sink. Do not tighten. Note that there are two sets

of mounting holes on the HS20). Holes on one edge allow

room between the DUT and evaluation board for the MS06

socket. The holes on the other edge are for direct through

hole mounting of the DUT to the evaluation board. It is rec-

ommended that you use the MS06.

http://www.cirrus.com

Use the supplied thermal washers or ther-

mal grease between the power amplifier

and the heat sink.

P r o d u c t I n n o v a t i o n F r o m

EK06 SA60

Evaluation Kit for SA60 Pin-Out

4. Mount the DUT to the HS20 by sliding under the head of the

5. Install leads of the DUT into the MS06 on the evaluation board.

PARTS LIST

Part #

HS20

EVAL11

MS06

OX7R105KWN

CSR07

TWO7

HS22

BEFORE YOU GET STARTED

• All Apex Precision Power amplifiers should be handled using

• Always use the heat sink and thermal washers included in

• Always use adequate power supply bypassing.

• Do not change connections while the circuit is powered.

• Initially set all power supplies to the minimum operating levels

• Check for oscillations.

• Power ground and signal ground must be separated to avoid

#6 screw and on top of the thermal washer. Tighten the nut

to the specified 8 to 10 in-lbs. (.9 to .13 N*M). Do not over

torque.

Use #6 self-tapping screws to secure the evaluation board

to the HS20 heat sink as shown in the assembly diagram

(Figure 1).

proper ESD precautions.

this kit.

allowed in the device data sheet.

switching noise in the DUT.

Description

Heatsink

PC Board

Mating Socket

1µF Ceramic Capacitor

Thermal Washer

Heatsink

1% Resistor

APEX − EK06UREVD

EK06

MAY 2009

Quantity

1 package

EK06

Related parts for EK06

EK06 Summary of contents

Page 1

... See the SA60 data sheet for help in selecting these components. 1uF capacitors and a .10Ω resistor have been included with the EK06 kit but may be replaced with other components as necessary. C1, not provided, should be selected for the voltage required by the application. See Apex Precision Power Application Note 30 for guidelines in selecting this bypass capacitor ...

Page 2

... EK06 FIGURE 2. TOP SIDE IC SIGNAL GND SIGNAL GND PWM DISABLE INPUT BOTTOM SIDE GND SIGNAL VCC Vcc IC EVAL11 Rsense A REV INPUT Vcc A OUT 5.50 REV-D EVAL11 DUT ISENSE A Rsense B ISENSE B PWR +Vs GND B OUT 1 12 3.00 EK06U ...

Page 3

... Cirrus Logic, Cirrus, and the Cirrus Logic logo designs, Apex Precision Power, Apex and the Apex Precision Power logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. EK06U EK06 3 ...

Related keywords

EK06 datasheet
EK06 data sheet
EK06 pdf datasheet
EK06 component
EK06 part
EK06 distributor
EK06 RoHS
EK06 datasheet download