JW2SN-B-DC18V Panasonic Electric Works, JW2SN-B-DC18V Datasheet - Page 3

• Manufacturer Part Number: JW2SN-B-DC18V
• Description: RELAY POWER 5A 18VDC SEALED PCB
• Manufacturer: Panasonic Electric Works
• Series: JWr

Specifications of JW2SN-B-DC18V

• Relay Type: General Purpose
• Contact Form: DPDT (2 Form C)
• Contact Rating (current): 5A
• Switching Voltage: 250VAC
• Coil Type: Standard
• Coil Current: 29mA
• Coil Voltage: 18VDC
• Turn On Voltage (max): 12.6 VDC
• Turn Off Voltage (min): 1.8 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Circuit: DPDT (2 Form C)
• Contact Rating @ Voltage: 5A @ 250VAC
• Control On Voltage (max): 12.6 VDC
• Control Off Voltage (min): 1.8 VDC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2. Specifications
* Specifications will vary with foreign standards certification ratings.
Notes: *1. This value can change due to the switching frequency, environmental conditions, and desired reliability level, therefore it is recommended to check this with the
REFERENCE DATA
JW 1 Form A Standard (5A) type
1. Maximum operating power
Contact
Rating
Electrical
characteristics
Mechanical
characteristics
Expected life
Conditions
Unit weight
Characteristics
100
10
*2. Wave is standard shock voltage of 1.2 50 s according to JEC-212-1981
*3. The upper limit of the ambient temperature is the maximum temperature that can satisfy the coil temperature rise value. Refer to Usage, transport and storage
*4. The pick-up and drop out voltages rise approximately 0.4% for every 1 C
1
actual load.
conditions in NOTES.
where the ambient temperature is high, please take into consideration the rise in pick-up and drop out voltages and keep the coil applied voltage within the
maximum applied voltage.
DC resistive
load
Contact material
Arrangement
Contact resistance (Initial)
Nominal switching capacity (resistive load)
Max. switching power (resistive load)
Max. switching voltage
Max. switching current
Min. switching capacity (reference value)*
Insulation resistance (Initial)
Breakdown voltage
(Initial)
Temperature rise (coil)
Surge breakdown voltage*
(Between contact and coil) (Initial)
Operate time (at nominal voltage) (at 20 C
Release time (at nominal voltage) (at 20 C
Shock resistance
Vibration resistance
Mechanical (at 180 times/min.)
Electrical (at 6 times/min.)
Conditions for operation, transport and storage*
Max. operating speed
(at nominal switching capacity)
10
Contact voltage, V
AC resistive
load
100
Between open contacts
Between contact and coil
Between contact sets
Functional
Destructive
Functional
Destructive
Item
All Rights Reserved © COPYRIGHT Panasonic Electric Works Co., Ltd.
1,000
2
2. Operate/release time
Sample: JW1aSN-DC12V-F, 10 pcs.
Ambient temperature: 20 C
1
68
68
10
F)
F)
5
0
3
(resistive method, with nominal coil voltage and
80
1 Form A, 1 Form C, 2 Form A and 2 Form C
at nominal switching capacity, at 20 C
Min. 1,000M (at 500V DC) Measurement at same location as “Breakdown voltage” section.
Release time
1 Form C, 2 Form A and 2 Form C:
90
Coil applied voltage, %V
1 Form A: Max. 45 C
33.8 F
5A 250V AC, 5A 30V DC
Humidity: 5 to 85% R.H. (Not freezing and condensing at low temperature)
100
Operate time
3,000 Vrms for 1 min. (2 Form A, 2 Form C) (Detection current: 10 mA)
68 F
98 m/s
Max. 55 C
Ambient temperature*
10 to 55 Hz at double amplitude of 1.6 mm (Detection time: 10 s.)
1,250VA, 150W
Standard type
given a standard ambient temperature of 20 C
110
Flux-resistant type: 20 times/min., Sealed type: 6 times/min.
Max. 5 ms (excluding contact bounce time) (Without diode)
2
5A
(Half-wave pulse of sine wave: 11 ms; detection time: 10 s.)
1,000 Vrms for 1 min. (Detection current: 10 mA)
5,000 Vrms for 1 min. (Detection current: 10 mA)
120
980 m/s
1 Form C, 2 Form A and 2 Form C: AgNi type
Max. 15 ms (excluding contact bounce time.)
131 F
Max.
Min.
Max.
Min.
x -
x -
Max. 100 m (By voltage drop 6 V DC 1A)
10 to 55 Hz at double amplitude of 2.0 mm
(Class B: –40 C to +85 C
113
2
(Half-wave pulse of sine wave: 6 ms.)
Min. 10
F,
1 Form A: AgSnO
4
: –40 C to +60 C
Approx. 13 g
250V AC, 30V DC
68
100mA, 5V DC
Specifications
5
Min. 5 10
F)
10,000 V
(at resistive load)
3. Life curve
1 Form A Standard (5 A) type
(resistive method, with nominal coil voltage and
100
at nominal switching capacity, at 20 C
10
.46 oz
6
–40 F to 185
2
–40 F to 140 F
type
1 Form A: Max. 45 C
1 Form C: Max. 55 C
10A 250V AC, 10A 30V DC
1 Form A and 1 Form C
68
High capacity type
250 V AC resistive load
2,500VA, 300W
30 V DC resistive load
5
F. Therefore, when using relays
F)
Contact current, A
10A
(Class E),
10
113
131 F
F,
15
68
JW
F)