G5V-2-DC48 Omron, G5V-2-DC48 Datasheet - Page 4

• Manufacturer Part Number: G5V-2-DC48
• Description: RELAY DPDT 2A 48VDC PCB
• Manufacturer: Omron
• Series: G5V-2r

Specifications of G5V-2-DC48

• Coil Type: Standard
• Coil Current: 12mA
• Relay Type: General Purpose
• Circuit: DPDT (2 Form C)
• Contact Rating @ Voltage: 2A @ 30VDC
• Coil Voltage: 48VDC
• Control On Voltage (max): 36 VDC
• Control Off Voltage (min): 2.4 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Contact Form: 2 Form C
• Power Consumption: 530 mW
• Contact Carry Current: 2 A
• Maximum Switching Current: 2 A
• Contact Rating: 0.50 A at 125 VAC, 2 A at 30 VDC
• Contact Configuration: DPDT
• Contact Current Max: 2A
• Contact Voltage Ac Nom: 125V
• Contact Voltage Dc Nom: 30V
• Coil Voltage Vdc Nom: 48V
• Coil Resistance: 4000ohm
• Current, Rating: 0.5⁄2 AAC⁄ADC
• Diameter, Mounting: 0.039 in. Dia. (Hole)
• Dielectric Rating: 1000 VAC @ 50⁄60 Hz for 1 minute between coil and contacts
• Dimensions: 0.807 in. L x 0.398 in. W x 0.453 in. H
• Function: Sensitive
• Material, Contact: Ag (Au clad)
• Number Of Pins: 8
• Power, Rating: 62.5⁄60 VA⁄W
• Standards: UL, CSA, FCC, RoHS
• Temperature, Operating, Maximum: 70 °C
• Temperature, Operating, Minimum: -25 °C
• Voltage, Control: 48 VDC
• Voltage, Rating: 125 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: G5V-2-DC48; G5V2DC48; Z2255

Dimensions
Note: 1. All units are in millimeters unless otherwise indicated.
G5V-2, G5V-2-H1
■ Approvals
UL Recognized (File No. E41515) / CSA Certified (File No. LR31928) - - Ambient Temp. = 40°C
Note: 1. The rated values approved by each of the safety standards may be different from the performance characteristics individually defined in this catalog.
Precautions
Long-term Continuously ON Contacts
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. Be sure to use a
fail-safe circuit design that provides protection against contact failure
or coil burnout.
80
G5V-2
G5V-2-H1
2. Tolerance: ±0.1
3. Orientation marks are indicated as follows:
2. In the interest of product improvement, specifications are subject to change.
Type
Low Signal Relay
DPDT
0.5
20.5 max.
20.3 typ.
Contact form
G5V-2
0.3
3 to 48 VDC
3 to 48 VDC
10.1 max.
9.9 typ.
7.62
Coil rating
3.5
0.5
11.5 max.
11.4 typ.
Terminal Arrangement/
Internal Connections
(Bottom View)
Relay Handling
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold clean-
ing bath immediately after soldering.
16
1
0.6 A at 125 VAC (General Use)
0.6 A at 110 VDC (Resistive)
2 A at 30 VDC (Resistive)
0.5 A at 125 VAC (General Use)
0.2 A at 110 VDC (Resistive)
1 A at 24 VDC (Resistive)
13
4
11
6
9
8
(1.3)
Eight, 1-dia. holes
Contact ratings
7.62
Tolerance: ±0.1
Mounting Holes
(Bottom View)
5.08 5.08
7.62
(1.3)
(1.2)