RELAY LATCHING PC MNT 24VDC

G6HK-2-DC24

Manufacturer Part NumberG6HK-2-DC24
DescriptionRELAY LATCHING PC MNT 24VDC
ManufacturerOmron
SeriesG6H
G6HK-2-DC24 datasheets
 


Specifications of G6HK-2-DC24

Coil TypeLatching, Dual CoilCoil Current12.5mA
Relay TypeTelecomCircuitDPDT (2 Form C)
Contact Rating @ Voltage1A @ 30VDCCoil Voltage24VDC
Control On Voltage (max)18 VDCMounting TypeThrough Hole
Termination StylePC PinContact ConfigurationDPDT
Contact Current Max1AContact Voltage Ac Nom125V
Contact Voltage Dc Nom30VCoil Voltage Vdc Nom24V
Coil Resistance1920ohmContact Form2 Form C
Power Consumption300 mWMaximum Switching Current1 A
Current, Rating0.5⁄1 AAC⁄ADCFunctionLatching
Number Of Pins10Power, Rating62.5⁄33 VA⁄W
StandardsUL, CSA, RoHSVoltage, Control24 VDC
Voltage, Rating125 VACLead Free Status / RoHS StatusLead free / RoHS Compliant
Control Off Voltage (min)-Other namesG6HK2DC24
Z967
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
9
Page 9
10
Page 10
Page 1/10

Download datasheet (520Kb)Embed
Next
Low Signal Relay
G6H
Ultra-compact, Ultra-sensitive DPDT Relay
• Compact size and low 5 mm profile.
• Low thermoelectromotive force.
• Low magnetic interference enables high-density mounting.
• Utilizes Omron’s moving-loop design.
• Highly stable magnetic circuit for latching endurance and
excellent resistance to vibration and shock.
• High sensitivity with low nominal power consumption.
• Single or dual coil latching types available.
• RoHS Compliant
Ordering Information
To Order: Select the part number and add the desired coil voltage rating, (e.g., G6H-2-DC6).
■ Non-latching
Terminal Type
Through-hole
DPDT
Surface mount
■ Latching
Terminal Type
Through-hole
DPDT
Specifications
■ Contact Data
Load
Rated load
Contact material
Carry current
Max. operating voltage
Max. operating current
Max. switching capacity
Min. permissible load (See note)
λ
–6
Note: P level:
= 0.1 x 10
/operation
60
This value was measured at a switching frequency of 120 operations/min and the criterion of contact resistance is 50 Ω. This value may vary
depending on the operating environment. Always double-check relay suitability under actual operating conditions.
DISCONTINUED
Contact form
G6H-2
G6H-2F
Contact form
Single coil latching
G6HU-2
Resistive load (p.f. = 1)
0.50 A at 125 VAC, 1 A at 30 VDC
Ag (Au clad)
1 A
125 VAC, 110 VDC
1 A
62.50 VA, 33 W
10 μA, 10 mVDC
Low Signal Relay
C
R
Model
Model
Dual coil latching
G6HK-2
G6H
49

G6HK-2-DC24 Summary of contents

  • Page 1

    ... Always double-check relay suitability under actual operating conditions. DISCONTINUED Contact form G6H-2 G6H-2F Contact form Single coil latching G6HU-2 Resistive load (p. 0. 125 VAC VDC Ag (Au clad 125 VAC, 110 VDC 1 A 62.50 VA μA, 10 mVDC Low Signal Relay C R Model Model Dual coil latching G6HK-2 G6H 49 ...

  • Page 2

    ... Rated voltage Rated current Coil (VDC) (mA) resistance (Ω) 3 33. 250 6 16.70 360 9 11.10 810 12 8.30 1,440 24 6.25 3,840 Dual Coil Latching Type (G6HK-2) Rated voltage Rated current Coil (VDC) (mA) resistance (Ω) 3 66. 125 6 33.30 180 9 22.20 405 12 16.70 720 24 12.50 1,920 Note: 1. The rated current and coil resistance are measured at a coil temperature of 23° ...

  • Page 3

    ... The insulation resistance was measured with a 500-VDC megohmmeter applied to the same parts as those for checking the dielectric strength. (The insulation resistance between the set and reset coil (G6HK-2), however, is 100MΩ min. when measured with a 125-VDC megohmmeter). 4. The above values are initial values. ...

  • Page 4

    ... Condition: The Units were shocked at the rate of 500 m/s three times each in the ±X, ±Y, and ±Z directions with and without voltage imposed on the Units until the Units malfunctioned. 30-VDC resistive load Dual Coil Latching (G6HK- VDC 24 VDC Ambient temperature (°C) 2 ...

  • Page 5

    High-frequency Characteristics (See notes 1 and 2.) Frequency vs. Isolation (Average value) 0 Unit: G6H-2 Unit: G6H-2 Number of Units 100 100 200 500 1,000 Frequency (MHz) Distribution of Operate and Release Time (See note ...

  • Page 6

    ... G6H-2F 14.3 max. (14.1)* 6.6 max. (6.3)* ■ Latching G6HU-2 14.3 max. (14.1)* 0.25 5.4 max. (5.0)* 3.5 2.54 G6HK-2 14.3 max. (14.1)* 0.25 5.4 max. (5.0)* 3.5 2.54 G6H 54 Low Signal Relay DISCONTINUED Terminal Arrangement/ Internal Connections 9.3 max. ...

  • Page 7

    ... VDC 0.5 A, 125 VAC Tape Packing (Surface Mounting Terminal Models) When ordering Relays in tape packing, add the prefix “-TR” to the model number otherwise the Relays in stick packing will be provided. Relays per Reel: 500 Direction of Relay Insertion Orientation mark Top tape (cover tape) ...

  • Page 8

    ... Claw Securing Force During Automatic Mounting During automatic insertion of Relays, be sure to set the securing force of each claw to the following so that the Relay’s characteristics will be maintained. C ...

  • Page 9

    ... Seller within 30 days of receipt of shipment. III. PRECAUTIONS 1. Suitability THE BUYER’S SOLE RESPOINSIBILITY TO ENSURE THAT ANY OMRON PRODUCT IS FIT AND SUFFICIENT FOR USE IN A MOTORIZED VEHICLE APPLICATION. BUYER SHALL BE SOLELY RESPONSIBLE FOR DETERMINING APPROPRIATENESS OF THE PARTICULAR PRODUCT WITH RESPECT TO THE BUYER’ ...

  • Page 10

    ... THE OMRON PRODUCT IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Complete “Terms and Conditions of Sale” for product purchase and use are on Omron’s website at http://www.components.omron.com – under the “About Us” tab, in the Legal Matters section. ...