G6A-434P-ST-US-DC24 Omron, G6A-434P-ST-US-DC24 Datasheet - Page 8

• Manufacturer Part Number: G6A-434P-ST-US-DC24
• Description: RELAY PC MNT 1A 4PDT 24VDC
• Manufacturer: Omron
• Series: G6Ar

Specifications of G6A-434P-ST-US-DC24

• Coil Type: Standard
• Coil Current: 15mA
• Relay Type: General Purpose
• Circuit: 4PDT (4 Form C)
• Contact Rating @ Voltage: 1A @ 30VDC
• Coil Voltage: 24VDC
• Control On Voltage (max): 16.8 VDC
• Control Off Voltage (min): 2.4 VDC
• Mounting Type: Through Hole
• Termination Style: PC Pin
• Contact Configuration: 4PDT
• Contact Current Max: 2A
• Contact Voltage Ac Nom: 125V
• Contact Voltage Dc Nom: 30V
• Coil Voltage Vdc Nom: 24V
• Contact Form: 4 Form C
• Power Consumption: 360 mW
• Maximum Switching Current: 2 A
• Contact Rating: 0.30 A at 125 VAC, 1 A at 30 VDC
• Current, Rating: 0.3⁄1 AAC⁄ADC
• Diameter, Mounting: 0.04 in.
• Dielectric Rating: 1000 VAC, 50⁄60 Hz for 1 Minute Between Coil and Contacts, Contacts of Different Poles, Contacts of Same Pole, 250 VAC, 50⁄60 Hz for 1 Minute Between Set and Reset Coils
• Dimensions: 1.39 in. (Max.) L x 0.40 in. (Max.) W x 0.45 in. (Max.) H
• Function: Sensitive
• Material, Contact: AgPd (Au Clad)
• Number Of Pins: 14
• Power, Rating: 125⁄60 VA⁄W
• Standards: UL, CSA
• Temperature, Operating, Maximum: 70 °C
• Temperature, Operating, Minimum: -40 °C
• Termination: Solder
• Voltage, Control: 24 VDC
• Voltage, Rating: 125 VAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: G6A-434P-STUS-DC24; G6A434PSTUSDC24; Z941

G6AK-274P-ST(40)-US
G6AU-474P-ST-US
G6AK-474P-ST(40)-US
Precautions
Long-term Continuously ON Contacts
Using the Relay in a circuit where the Relay will be ON continuously
for long periods (without switching) can lead to unstable contacts
because the heat generated by the coil itself will affect the insulation,
causing a film to develop on the contact surfaces. Be sure to use a
fail-safe circuit design that provides protection against contact failure
or coil burnout. Otherwise, use a latching relay.
88
Low Signal Relay
- DISCONTINUED
- DISCONTINUED
0.6
20.2 max.
(20)*
0.6
G6A
0.6
*Average value
35.4 max.
(35.2)*
0.3
35.4 max.
(35.2)*
10.1 max.
(9.9)*
7.62
*Average value
0.64
*Average value
0.3
8.4 max.
(8.2)*
3.16
0.3
10.1 max.
(9.9)*
7.62
10.1 max.
(9.9)*
Terminal Arrangement/
Internal Connections
(Bottom View)
16
Relay Handling
When washing the product after soldering the Relay to a PCB, use a
water-based solvent or alcohol-based solvent, and keep the solvent
temperature to less than 40°C. Do not put the Relay in a cold clean-
ing bath immediately after soldering.
1
7.62
+
-
S R
+
-
0.64
Fourteen, 1.0-dia. holes
Sixteen, 1.0-dia. holes
15
2
0.64
4
13
8.4 max.
(8.2)*
3.16
11
6
8.4 max.
(8.2)*
3.16
(1.2)
9
8
5.08 5.08 5.08 2.54
10
5.08 5.08 5.08
Terminal Arrangement/
Internal Connections
(Bottom View)
7
Terminal Arrangement/
Internal Connections
(Bottom View)
10
Tolerance: ±0.1
7
Mounting Holes
(Bottom View)
Tolerance: ±0.1
Mounting Holes
(Bottom View)
(1.2)
Ten, 1-dia. holes
12
5
12
5
Mounting Holes
(Bottom View)
Tolerance: ±0.1
14
2.54
3
S
14
3
+
-
16
1
5.08
7.62
16
1
5.08
+ -
15
2
S R
- +
13
+
-
R
4
5.08 5.08
13
5.08 5.08
4
5.08 5.08
11
6
11
6
9
8
9
8
(1.2)
7.62
(1.2)
(1.2)
(1.2)
7.62
(1.2)
7.62
(1.2)
(1.2)
(1.2)
(1.2)