CRA06P043470KJTA Vishay, CRA06P043470KJTA Datasheet - Page 3

• Manufacturer Part Number: CRA06P043470KJTA
• Description: RES ARRAY 470K OHM 4 TRM 2RES SM
• Manufacturer: Vishay
• Series: CRA06r

Specifications of CRA06P043470KJTA

• Resistance (ohms): 470K
• Number Of Resistors: 2
• Circuit Type: Isolated
• Temperature Coefficient: ±200ppm/°C
• Tolerance: ±5%
• Power Per Element: 62.5mW
• Number Of Pins: 4
• Package / Case: 0606 (1616 Metric), Concave
• Size / Dimension: 0.063" L x 0.063" W (1.60mm x 1.60mm)
• Height: 0.024" (0.60mm)
• Mounting Type: Surface Mount
• Operating Temperature: -55°C ~ 155°C
• Lead Free Status / RoHS Status: Lead free by exemption / RoHS Compliant

CRA06P
Vishay
Notes
(1)
(2)
www.vishay.com
258
TEST PROCEDURES AND REQUIREMENTS
TEST
(clause)
Resistance (4.5)
Temperature coefficient (4.8.4.2)
Overload (4.13)
Solderability (4.17.5)
Resistance to soldering heat (4.18.2)
Rapid change of temperature (4.19)
Damp heat, steady state (4.24)
Climatic sequence (4.23)
Endurance at 70 °C (4.25.1)
Extended endurance (4.25.1.8)
Endurance at upper category
temperature (4.25.3)
APPLICABLE SPECIFICATIONS
• EN 60115-1
• EN 140400
• EN 140401-802
• IEC 60068-2-X
• EIA 481
Figures are given for a single element
Solderability is specified for 2 years after production or requalification. Permitted storage time is 20 years
(2)
Generic Specification
Sectional Specification
Detail Specification
Variety of environmental test procedures
Packaging of SMD components
For technical questions, contact: [e-mail]
CONDITIONS OF TEST
Stability for product types:
16 h at UCT = 125 °C; 1 cycle at 55 °C;
U = U
U = U
30 min at UCT = 125 °C; 5 cycles
Solder bath method; 235 °C; 2 s
Aging 4 h at 155 °C, dryheat
Duration extended to 8000 h
1 h/1 kPa at 15 °C to 35 °C;
30 min at LCT = - 55 °C;
(260 ± 5) °C; (10 ± 1) s
max.
max.
UCT = 125 °C; 1000 h
U = 2.5 × (P
1.5 h ON; 0.5 h OFF;
(40 ± 2) °C; 56 days;
2 h at LCT = - 55 °C;
Solder bath method;
Thick Film Resistor Array
Visual examination
20/- 55/20 °C and
≤ 2 x U
5 cycles at 55 °C
; whichever is less severe
; whichever is less severe
U = (P
U = (P
(93 ± 3) % RH
70 °C; 1000 h
20/125/20 °C
max.
70
70
-
EN 60115-1
x R)
x R)
70
; 0.5 s
x R)
1/2
1/2
1/2
CRA06P
CLASS 1 OR BETTER
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (0.25 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
10 Ω to 1 MΩ
± 100 ppm/K
STABILITY
PERMISSIBLE CHANGE (ΔR/R)
± 1 %
Good tinning (≥ 95 % covered)
REQUIREMENTS
no visible damage
Document Number: 31047
CLASS 2 OR BETTER
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)
± (2 % R + 0.1 Ω)
10 Ω to 1 MΩ
± 2 %; ± 5 %
± 200 ppm/K
Revision: 13-Oct-08
STABILITY
(1)