MCH032AN010CK Rohm Semiconductor, MCH032AN010CK Datasheet - Page 3

• Manufacturer Part Number: MCH032AN010CK
• Description: CAP CERAMIC 1.0PF 25V C0G 0201
• Manufacturer: Rohm Semiconductor

Specifications of MCH032AN010CK

• Capacitance: 1.0pF
• Voltage - Rated: 25V
• Tolerance: ±0.25pF
• Temperature Coefficient: C0G, NP0
• Mounting Type: Surface Mount, MLCC
• Operating Temperature: -55°C ~ 125°C
• Features: General Purpose
• Package / Case: 0201 (0603 Metric)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 511-1376-2; MCH032A010CK

Ceramic capacitors
!Characteristics
∗The design and specifications are subject to change without prior notice. Before ordering or using, please check the latest technical specification.
Class 1 (For thermal compensation)
Item
Operating temperature
Nominal capacitance (C)
Dissipation factor (tan δ )
Insulation resistance (IR)
Withstanding voltage
Temperature characteristics
Terminal adherence
Resistance
to vibration
Solderability
Resistance
to soldering
heat
Temperature
cycling
Humidity load
test
High-
temperature
load test
Temperature characteristics
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
Withstanding voltage
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
At least 3/4 of the surface of the two terminals
Must be within the specified tolerance range.
100/(400+20C)% or less: Less than 30 pF
± 2.5% or ± 0.25 pF, whichever is larger.
± 2.5% or ± 0.25 pF, whichever is larger.
± 7.5% or ± 0.75 pF, whichever is larger.
No detachment or signs of detachment.
± 3.0% or ± 0.3 pF, whichever is larger.
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
The insulation must not be damaged.
The insulation must not be damaged.
Must satisfy initial specified value.
Must satisfy initial specified value.
Must satisfy initial specified value.
must be covered with new solder.
Must be within initial tolerance.
0.1% or less : 30 pF or larger
10,000MΩ or 500MΩ ⋅ µF,
10,000MΩ or 500MΩ ⋅ µF,
10,000MΩ or 500MΩ ⋅ µF,
1,000MΩ or 50MΩ ⋅ µF,
500MΩ or 25MΩ ⋅ µF,
Within 0 ± 30ppm/°C
whichever is smaller
whichever is smaller
whichever is smaller
whichever is smaller
whichever is smaller
−55°C ~ 125°C
A (CG) (C0G)
0.5% or less
0.3% or less
Based on paragraph 7.8 and paragraph 9
Measured at room temperature and standard humidity,
1000pF or less Measurement frequency
Over 1000pF
Based on paragraph 7.1
Apply 300% of the rated voltage for 1 to 5s then measure.
The temperature coefficients in table 12, paragraph 7.12 are
calculated at 20° C and high temperature.
Based on paragraph 8.11. 2.
Apply 2N for 10 ± 1s in the
direction indicated by the arrow.
Chip is mounted to a board in the manner
shown on the right, subjected to vibration
(type A in paragraph 8.2), and measured
24 ± 2 hrs. later.
Based on paragraph 8.13
Based on paragraph 8.14.
Based on paragraph 9.3
Based on paragraph 9.9
Based on paragraph 9.10
Based on paragraph 7.6
Measurement is made after rated voltage is applied for 60 ± 5s.
Soldering temperature
Soldering time
Preheating
Soldering temperature
Soldering time
Number of cycles : 5
Capacitance measured after 24 ± 2 hrs.
Test temperature
Relative humidity
Applied voltage
Test time
Capacitance measured after 24 ± 2 hrs.
Test temperature
Applied voltage
Test time
Capacitance measured after 24 ± 2 hrs.
Measurement voltage
Measurement frequency
Measurement voltage
Test methods/conditions
(based on JIS C 5102)
: 40 ± 2° C
: 90% to 95%
: rated voltage
: 500 to 524 hrs.
: Max. operating temp.
: rated voltage × 200%
: 1,000 to 1,048 hrs.
: 260 ± 5° C
: 5 ± 0.5s
: 150 ± 10° C for 1 to 2 min.
: 235 ± 5° C
: 2 ± 0.5s
: 1 ± 0.1MHz
: 1 ± 0.1Vrms.
: 1 ± 0.1kHz
: 1 ± 0.1Vrms.
MCH03
Board
Capacitor
Pressure (2N)
Test board
3/6