MCH155A6R2DK Rohm Semiconductor, MCH155A6R2DK Datasheet - Page 5

• Manufacturer Part Number: MCH155A6R2DK
• Description: CAP CERAMIC 6.2PF 50V C0G 0402
• Manufacturer: Rohm Semiconductor

Specifications of MCH155A6R2DK

• Capacitance: 6.2pF
• Voltage - Rated: 50V
• Tolerance: ±0.5pF
• Temperature Coefficient: C0G, NP0
• Mounting Type: Surface Mount, MLCC
• Operating Temperature: -55°C ~ 125°C
• Features: General Purpose
• Package / Case: 0402 (1005 Metric)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 511-1024-2

Ceramic capacitors
∗The design and specifications are subject to change without prior notice. Before ordering or using, please check the latest technical specification.
Class 2 (High dielectric constant)
Item
High-
temperature
load test
Operating temperature
Nominal capacitance (C)
Dissipation factor (tan δ)
Insulation resistance (IR)
Temperature characteristics
Terminal adherence
Solderability
Temperature
cycling
Withstanding voltage
Resistance
to vibration
Resistance
to soldering
heat
Humidity load
test
Temperature characteristics
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
Withstanding voltage
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
Appearance
Rate of capacitance change
Dissipation factor (tan δ)
Insulation resistance
(when rated voltage is 16V: 3.5% or less)
At least 3/4 of the surface of the two terminals must be covered with new solder.
CN (R) (B) (X7R)
−55°C ~ +125°C
± 12.5% or less
Within ± 10.0%
Within ± 5.0%
Within ± 7.5%
Within ± 15%
2.5% or less
5.0% or less
5.0% or less
10,000MΩ or 500MΩ ⋅ µF, whichever is smaller
10,000MΩ or 500MΩ ⋅ µF, whichever is smaller
10,000MΩ or 500MΩ ⋅ µF, whichever is smaller
1,000MΩ or 50MΩ ⋅ µF, whichever is smaller
Must be within the specified tolerance range.
500MΩ or 25MΩ ⋅ µF, whichever is smaller
No detachment or signs of detachment
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
There must be no mechanical damage.
The insulation must not be damaged.
The insulation must not be damaged.
Must satisfy initial specified value.
Must satisfy initial specified value.
Must satisfy initial specified value.
Must be within initial tolerance.
(when rated voltage is 16V: 7.5% or less)
(when rated voltage is 16V: 10.0%)
(when rated voltage is 16V: 10.0%)
Within ± 20.0%
Within ± 20.0%
Within ± 30.0%
Within ± 30.0%
−30°C ~ +85°C
FN (F) (Y5V)
7.5% or less
7.5% or less
5.0% or less
+ 22, + 82%
Based on paragraph 7.8
Measured at room temperature and standard humidity,
Measurement frequency
Measurement voltage
Based on paragraph 7.6
Measurement is made after rated voltage
is applied for 60 ± 5s.
Based on paragraph 7.1
Apply 250% of the rated voltage for 1 to 5s then measure.
The temperature coefficients in paragraph 7.12,
table 8, condition B, are based on measurements
carried out at 20 ° C, with no voltage applied.
Based on paragraph 8. 11. 2.
Apply 5N for 10 ± 1s
in the direction indicated
by the arrow.
Chip is mounted to a board in the
manner shown on the right, subjected
to vibration (type A in paragraph 8.2),
and measured 48 ± 4 hrs. later.
Based on paragraph 8. 13
Based on paragraph 8. 14.
Soldering temperature
Soldering time
Preheating
Based on paragraph 9.3
Based on paragraph 9.9
Based on paragraph 9.10
Soldering temperature
Soldering time
Number of cycles : 5
Capacitance measured after 48 ± 4 hrs.
Test temperature
Relative humidity
Applied voltage
Test time
Capacitance measured after 48 ± 4 hrs.
Test temperature
Applied voltage
Test time
Capacitance measured after 48 ± 4 hrs.
Test methods/conditions
(based on JIS C 5102)
: 260 ± 5°C
: 5 ± 0.5s
: 150 ± 10°C for
: 1 ± 0.1 kHz
: 1.0 ± 0.2 Vrms.
1 to 2 min.
: 40 ± 2°C
: 90% to 95%
: rated voltage
: 500 to 524 hrs.
: Max. operating temp.
: rated voltage × 200%
: 1,000 to 1,048 hrs.
: 235 ± 5°C
: 2 ± 0.5s
Capacitor
MCH15
Pressure (5N)
Test board
Board