EEE-HD1H100P Panasonic - ECG, EEE-HD1H100P Datasheet - Page 26

• Manufacturer Part Number: EEE-HD1H100P
• Description: CAP 10UF 50V ELECT HD SMD
• Manufacturer: Panasonic - ECG
• Series: HDr

Specifications of EEE-HD1H100P

• Capacitance: 10µF
• Voltage Rating: 50V
• Tolerance: ±20%
• Lifetime @ Temp.: 5000 Hrs @ 105°C
• Operating Temperature: -40°C ~ 105°C
• Features: General Purpose
• Ripple Current: 33mA
• Impedance: 4 Ohm
• Mounting Type: Surface Mount
• Package / Case: Radial, Can - SMD
• Size / Dimension: 0.248" Dia (6.30mm)
• Height: 0.228" (5.80mm)
• Surface Mount Land Size: 0.260" L x 0.260" W (6.60mm x 6.60mm)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Esr (equivalent Series Resistance): -
• Other names: EEEHD1H100P; PCE4976TR

3. Precautions for using capacitors
3.1 Environmental Conditions
3.2 Electrical Precautions
4. Emergency Procedures
5. Long Term Storage
5.1 Environmental Conditions
6. Capacitor Disposal
(1) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor.
(2) Direct contact with water, salt water, or oil.
(3) High humidity conditions where water could condense on the capacitor.
(4) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, Chlorine compound, Bromine, Bromine compound or
(5) Exposure to ozone, radiation, or ultraviolet rays.
(6) Vibration and shock conditions exceeding specified requirements.
(2) Avoid contact with the escaping electrolyte gas, which can exceed 100 ℃ temperatures.
(1) Exposure to temperatures above the upper category or below the lower category temperature of the capacitor.
(2) Direct contact with water, salt water, or oil.
(3) High humidity conditions where water could condense on the capacitor.
(4) Exposure to toxic gases such as hydrogen sulfide, sulfuric acid, nitric acid, chlorine, Chlorine compound, Bromine, Bromine compound or
(5) Exposure to ozone, radiation, or ultraviolet rays.
(6) Vibration and shock conditions exceeding specified requirements.
When disposing capacitors, use one of the following methods.
(1) Incinerate after crushing the capacitor or puncturing the can wall (to prevent explosion due to internal pressure rise).
(2) Dispose as solid waste.
(1) Avoid touching the terminals of a capacitor as a possible electric shock could result. The exposed aluminum case is not insulated and
(2) Avoid short circuiting the area between the capacitor terminals with conductive materials including liquids such as acids or alkaline
(3) A low-molecular-weight-shiroxane which is included in a silicon material shall causes abnormal electrical characteristics.
(1) If the pressure relief of the capacitor operates, immediately turn off the equipment and disconnect from the power source.
Leakage current of a capacitor increases with long storage times. The aluminum oxide film deteriorates as a function of temperature and time.
If used without reconditioning, an abnormally high current will be required to restore the oxide film.
This surge current could cause the circuit or the capacitor to fail.
Storage period is one year.
For storage condition, keep room temperature (5℃～35℃) and humidity (45%～85%) where direct sunshine doesn't reach.
voltage in series with a 1000 Ω current limiting resistor for a time period of 30 minutes.
Capacitors should not be stored or used in the following environments.
ammonia.
If electrolyte or gas enters the eye, immediately flush the eye with large amounts of water.
If electrolyte or gas is ingested by mouth, gargle with water.
If electrolyte contacts the skin, wash with soap and water.
ammonia.
NOTE : Local laws may have specific disposal requirements which must be followed.
This will minimize an additional damage caused by the vaporizing electrolyte.
could also cause electric shock if touched.
solutions.
Panasonic Electronic Devices Co.,Ltd.
Product Specification
When storage period is over 12 months, a capacitor should be reconditioned by applying the rated
Application Guidelines
Guideline-ALV-S2-3
Guidelines-4