@Super low ESR, impedance and high heat resistance have been obtained by using
@Rated voltage range : 2.5 to 16V
@Case size range : F5B5.7L to F8B6.7L
@Suitable for DC-DC converters, voltage regulators and decoupling applications used to
@RoHS Compliant
?SPECIFICATIONS
*Note : If any doubt arises, measure the leakage current after following voltage treatment.
?PART NUMBERING SYSTEM
?DIMENSIONS [mm]
@Terminal Code : A
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Surge Voltage
Leakage Current
Dissipation Factor
(tane)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Bias Humidity
Surge Voltage
Failure Rate
A P X C
conductive polymer as electrolyte.
(ESR and rated ripple current values are improved from PXA series.)
computer motherboards etc.
1
2
Items
3
Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C.
LP0.3
4
0.3max.
A A A
5
6
CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS
7
A R A
8
-55 to +105C
2.5 to 16V
P20% (M)
Rated voltage(V)B1.15
I=0.2CV (max.)
I : Max. leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (V
0.12 max.
Z(-25C)/Z(+20C)[1.15
Z(-55C)/Z(+20C)[1.25
The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 1,000 hours
at 105C.
Appearance
Capacitance change
DF (tanE)
ESR
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at
60C, 90 to 95% RH for 500 hours.
Appearance
Capacitance change
DF (tanE)
ESR
Leakage current
The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds
through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds.
Appearance
Capacitance change
DF (tanE)
ESR
Leakage current
1% per 1,000 hours maximum (Confidence level 60% at 105C)
9
10
A A A
11
W
AP0.2
12 13
dc
M
dc
14
, Capacitance range : 27 to 470MF
A A A
15
Capacitance code (ex. 27MF:270,100MF:101)
16 17
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
No significant damage
[P20% of the initial value
[150% of the initial specified value
[150% of the initial specified value
[The initial specified value
G
18
Voltage code (ex. 6.3V:6R3,10V:100)
Size code
E60
F60
H70
Capacitance tolerance code
6.3
fD
5
8
Supplement code
Terminal code
5.7
5.7
6.7
L
Taping code
Series code
Size code
(1/2)
Category
5.3
6.6
8.3
A
Characteristics
5.3
6.6
8.3
B
Please refer to "A guide to global code (conductive polymer type)"
5.9
7.2
9.0
C
0.5 to 0.8
0.5 to 0.8
0.7 to 1.1
W
dc
1.4
1.9
3.1
P
)
(at 20C after 2 minutes)
CAT. No. E1001F
?MARKING
EX) 4V220MF
Surface Mount
(at 20C, 120Hz)
(at 20C, 120Hz)
C
220
(at 100kHz)
4
28M
(at 105C)
V