S330K29C0GN65K6R Vishay, S330K29C0GN65K6R Datasheet
S330K29C0GN65K6R
Specifications of S330K29C0GN65K6R
Related parts for S330K29C0GN65K6R
S330K29C0GN65K6R Summary of contents
Page 1
... General Information Vishay BCcomponents Ceramic Disc, RFI and Safety Capacitors IN ACCORDANCE WITH IEC RECOMMENDATIONS CERAMIC CAPACITORS ARE SUBDIVIDED INTO TWO CLASSES: • CERAMIC CLASS 1 or low-K capacitors are mainly manufactured of titanium dioxide or magnesium silicate • CERAMIC CLASS 2 or high-K capacitors contain mostly alkaline titanates • ...
Page 2
... For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents CLASS 2 C 100 pF 1 kHz, 1.0 V ± 0.2 V RMS RMS C < 100 pF 1 MHz, 1.0 V ± 0.2 V RMS RMS measuring voltage = (10 ± measuring voltage = (100 ± 15) V measuring voltage = (500 ± ...
Page 3
... General Information Vishay BCcomponents CAPACITANCE CODING SYSTEM CAPACITANCE VALUE CAPACITANCE TOLERANCE RATED VOLTAGE CERAMIC DIELECTRIC Notes • The types of ceramic in bold print are standard versions, the color coding is applied to the top edge of the capacitor. • The actual markings are given in detail on the respective datasheet. ...
Page 4
... S Upper category temperature TEMPERATURE CODE FIGURE + 45 ° ° ° 105 ° 125 °C 7 For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents Temperature range: upper and lower temperature limits in °C TEMPERATURE RANGE CODE FIGURE - 125 Admissible capacitance change related to 25 °C over the ...
Page 5
... General Information Vishay BCcomponents CLASS 1 CERAMIC TYPE TEMPERATURE COEFFICIENT OF THE CAPACITANCE FOR CLASS 1 CERAMIC CAPACITORS C [%] = 100 150 100 - 100 120 VOLTAGE DEPENDENCE OF CAPACITANCE None FREQUENCY DEPENDENCE OF CAPACITANCE Max MHz DISSIPATION FACTOR • For values greater than 50 pF: see datasheet • For lower values the dissipation factor is calculated according to the type of ceramic (rated temperature coefficient) under consideration of the capacitance acc 130600. • ...
Page 6
... Z5V - 3 CERAMIC DIELECTRIC: X5U 10 0 Y5V - For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents Typical % Capacitance Change at 25 °C X7R - Temperature °C Typical % Capacitance Change at 25 °C X5F - Temperature °C Typical % Capacitance Change at 25 °C Y5U - ...
Page 7
... General Information Vishay BCcomponents CAPACITANCE “AGING” OF CERAMIC CAPACITORS Following the final heat treatment, all class 2 ceramic capacitors reduce their capacitance value. According to logarithmic law, this is due to their special crystalline construction. This change is called “aging”. If the capacitors are heat treated (for example when soldering), the capacitance increases again to a higher value deaging, and the aging process begins again ...
Page 8
... Document Number: 28536 Revision: 07-Jan-10 40/085/ SET Maximum ambient temperature of operation (dry heat test) Category examples according to IEC 60068-1 For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents rd 3 SET Number of days (steady test state) 25/085/04 25/085/21 40/085/21 55/125/ ° ° ...
Page 9
... General Information Vishay BCcomponents STORAGE he capacitors must not be stored in a corrosive atmosphere, where sulphide or chloride gas, acid, alkali or salt are present. Exposure of the components to moisture, should be avoided. The solderability of the leads is not affected by storage months (temperature + 10 ° °C, relative humidity RH). Class 2 Ceramic Dielectric Capacitors are also subject to aging see previous page ...
Page 10
... By derating the voltage load, greatly increased reliability can be predicted. Temperature the maximum category temperature, is not believed to significantly affect the reliability. Document Number: 28536 Revision: 07-Jan-10 ), RFI safety cap 100 % short circuit ( RFI safety caps) For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents R www.vishay.com 11 ...
Page 11
... General Information Vishay BCcomponents PRODUCTION FLOWCHART Sinter process (firing) Screen printing of both electrodes Firing of electrodes Sorting in tolerance classes if necessary Forming and soldering leads Aligning for coating process Epoxy or phenol resin coating Hardening resin coat 100 % Test Visual Inspection Cutting leads for bulk packaging or taping www ...
Page 12
... NON-STANDARD LEAD STYLES AVAILABLE ON REQUEST Document Number: 28536 Revision: 07-Jan- outside crimp kinked leads D Tangent line Ø double crimp leads For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents L = straight leads D Tangent line diameter F = lead spacing SH = seated height T = thickness L = lead length DR = run down www.vishay.com 13 ...
Page 13
... General Information Vishay BCcomponents PACKAGING RADIAL TAPE AND AMMOPACK DESCRIPTION Body Dimension Feed Hole Diameter Wire Lead Diameter Lead End Protrusion Lead Spacing Height to seating plane (for straight leads) Height to seating plane (for kinked leads) Top of Component Height Body Inclination Rejected Component Cut Height ...
Page 14
... Fig. 2 Illustration for component pitch 25.4 mm Feed hole pitch 12.7 mm (for F = 7.5 and 10.0) Δh Δ Ø Detail A For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents Ammo Packaging direction of unreeling 340 max. 340 max. 55 max Δh ΔP Δ ...
Page 15
... General Information Vishay BCcomponents CLEAR TEXT ORDERING CODE D 471 Product Capacitance Capacitance Type Tolerance D = general The first two C = ± 0.25 pF type with digits are the D = ± 0.5 pF phenolic significant G = ± resin coat figures ± safety capacitance K = ± recognized and the last M = ± ...
Page 16
... V 7 All > 7.5 For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents STANDARD PACKAGING SPEC. SPQ DIMENSIONS (PCS (mm) 1000 1000 All (except 6 kV) 1000 500 245 x 120 x 65 250 500 6 kV 250 5000 3000 ...
Page 17
... General Information Vishay BCcomponents SIZE CODE SIZE CODE (CTC MEASUREMENT On the basis of the center of the product, measure the thickness with vernier caliper along every direction. Calipering position refers to the figure below. The maximum value is the thickness value. Vernier Caliper position for the diameter measurement www ...
Page 18
... Applied voltage should be the load such as self-generated heat is within 20 °C on the condition of environmental temperature 25 °C. Note, that excessive heat may lead to deterioration of the capacitor’s characteristics Document Number: 28536 Revision: 07-Jan- 0 For technical questions, contact: CDC@vishay.com General Information Vishay BCcomponents AC V p-p 0 www.vishay.com 19 ...