clc410 National Semiconductor Corporation, clc410 Datasheet
clc410
Available stocks
Related parts for clc410
clc410 Summary of contents
Page 1
... ADC driver. The low 160mW quiescent power consumption and very low 40mW disabled power consumption suggest use where power is critical and/or “system off” power consumption must be minimized. The CLC410 is available in several versions to meet a variety of requirements. A three letter suffix determines the version. Enhanced Solutions (Military/Aerospace) SMD Number: 5962-90600 Space level versions also available ...
Page 2
... Lead Solder Duration (+300˚C) ± 7V ESD Rating (human body model) Operating Ratings Thermal Resistance 60mA Package ± V MDIP CC 5V SOIC ± V −1V CC ± 250 ; unless specified f Conditions CLC410AJ < V 0.5V OUT PP < OUT < V 0.5V OUT 40MHz > 40MHz DC to 75MHz DC to 75MHz 0 ...
Page 3
... R = 100 , Symbol Parameter VDIS To Disable VEN To Enable DIS current (sourced from CLC410, see Figure 5 ) IDIS To Disable IEN To Enable OSD Off Isolation Static, DC Performance VIO Input Offset Voltage (Note 3) DVIO average temperature coefficient IBN Input Bias Current (Note 3) DIBN ...
Page 4
Typical Performance Characteristics fied). Non-Inverting Frequency Response Frequency Response for Various R 2nd and 3rd Harmonic Distortion www.national.com (T = 25˚ + Inverting Frequency Response 01274901 S Forward and Reverse Gain During Disable L ...
Page 5
Typical Performance Characteristics Specified). (Continued) Equivalent Input Noise Pulse Response Long-Term Settling Time (T = 25˚ + 01274907 01274928 Settling Time vs. Capacitive Load 01274924 5 ± 100 ; Unless CC ...
Page 6
Typical Performance Characteristics Specified). (Continued) Enable/Disable Response Differential Gain and Phase (4.43MHz) www.national.com (T = 25˚ + Differential Gain and Phase (3.58MHz) 01274910 01274912 6 ± 100 ; Unless CC L ...
Page 7
Application Division FIGURE 1. Recommended Non-Inverting Gain Circuit FIGURE 2. Recommended Inverting Gain Circuit 7 01274913 01274914 www.national.com ...
Page 8
... Application Division Enable/Disable Operation The CLC410 has an enable/disable feature that is useful for conserving power and for multiplexing the outputs of several amplifiers onto an analog bus ( Figure 3 ). Disabling an am- plifier while not in use reduces power supply current and the output and inverting input pins become a high impedance. ...
Page 9
... Understanding the Loop Gain The CLC410 is a current-feedback op amp. Referring to the equivalent circuit of Figure 7 , any current flowing in the inverting input is amplified to a voltage at the output through the transimpedance gain shown below. This Z(s) is analo- gous to the open-loop gain of a voltage feedback amplifier ...
Page 10
... Note OA-7 for active filter realizations with the CLC410. Offset Adjustment Pin Pin 1 can be connected to a potentiometer as shown in Figure 1 and used to adjust the input offset of the CLC410. Full range adjustment of input offset adjustment range. Pin 1 should always be by- passed to ground with a ceramic capacitor located close to the package for best settling performance ...
Page 11
Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin SOIC NS Package Number M08A 8-Pin MDIP NS Package Number N08E 11 www.national.com ...
Page 12
... NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant ...