LT1818 Linear Technology, LT1818 Datasheet
LT1818
Available stocks
Related parts for LT1818
LT1818 Summary of contents
Page 1
... The LT1818/LT1819 are manufactured on Linear Technology’s advanced low voltage complementary bipo- lar process. The LT1818 (single op amp) is available in SOT-23 and SO-8 packages; the LT1819 (dual op amp) is available in MSOP-8 and SO-8 packages. , LTC and LT are registered trademarks of Linear Technology Corporation. ...
Page 2
... S5 PART* MS8 PACKAGE MARKING 8-LEAD PLASTIC MSOP T = 150 C, JMAX LTF7 ORDER PART TOP VIEW NUMBER OUT A 1 LT1818CS8 – LT1818IS8 A + PART – MARKING S8 PACKAGE 8-LEAD PLASTIC SO 1818 T = 150 C, 1818I JMAX The denotes the specifications which apply over the full operating = 25 C ...
Page 3
... 500 V OUT P-P L HD3 5MHz 500 V OUT P 150 150 V L Per Amplifier – LT1818/LT1819 = 0V, unless otherwise noted. MIN TYP MAX 1.5 5 750 1.5 3.5 4 1.5 2.5 1.0 0.8 1.0 6 0.7 0.6 82 100 ...
Page 4
... LT1818/LT1819 ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T SYMBOL PARAMETER V Input Offset Voltage Input Offset Voltage Drift OS I Input Offset Current OS I Input Bias Current B e Input Noise Voltage Density n i Input Noise Current Density n R Input Resistance IN C Input Capacitance ...
Page 5
... Note 9: The LT1818C/LT1819C are guaranteed to meet specified performance from and is designed, characterized and expected to meet the extended temperature limits, but is not tested at –40 C and 85 C. The LT1818I/LT1819I are guaranteed to meet the extended temperature limits. Note 10: Thermal resistance ( metal connected to the package. The specified values are for short traces connected to the leads ...
Page 6
... LT1818/LT1819 W U TYPICAL PERFOR A CE CHARACTERISTICS Supply Current vs Temperature 12 PER AMPLIFIER 2. 125 –50 – 100 TEMPERATURE ( C) 18189 G01 Input Bias Current vs Temperature –0.4 –0.8 –1.2 –1 –2 2.5V S –2.4 –2.8 –50 – ...
Page 7
... R = 500 100 – 500 1pF F –10 1M 10M 100M FREQUENCY (Hz) 18189 G17 LT1818/LT1819 Output Impedance vs Frequency 100 A = 100 0.1 0.01 125 10k 100k 1M 10M FREQUENCY (Hz) = 500 GBW GBW PHASE MARGIN ...
Page 8
... LT1818/LT1819 W U TYPICAL PERFOR A CE CHARACTERISTICS Gain Bandwidth and Phase Margin vs Supply Voltage 450 GBW 500 400 L 350 GBW 300 R = 100 L PHASE MARGIN R = 100 L PHASE MARGIN R = 500 SUPPLY VOLTAGE ( V) 18189 G19 Slew Rate vs Input Step 2000 T =25 C ...
Page 9
... FREQUENCY (Hz) 18188 G29 Large-Signal Transient, A 2V/DIV 18189 G31 Large-Signal Transient 1V/DIV 18189 G33 S LT1818/LT1819 0.1% Settling Time INPUT TRIGGER (1V/DIV) OUTPUT SETTLING RESIDUE (5mV/DIV 5ns/DIV 18189 G30 2.5V OUT SETTLING TIME = 9ns A = – ...
Page 10
... Input Considerations The inputs of the LT1818/LT1819 amplifiers are con- nected to the bases of NPN and PNP bipolar transistors in parallel. The base currents are of opposite polarity and provide first order bias current cancellation ...
Page 11
... For example output step with a gain of 10 has a 0.6V input step, whereas at unity gain there input step. The LT1818/LT1819 is tested for slew rate at a gain of –1. Lower slew rates occur in higher gain configurations, whereas the highest slew rate (2500V/ s) occurs in a noninverting unity-gain configuration ...
Page 12
... LT1818/LT1819 U TYPICAL APPLICATIO Single Supply Differential ADC Driver 5V 18pF + 51.1 1/2 LT1819 – 18pF 536 536 – 51.1 1/2 LT1819 4.99k + 18pF 4.99k 0.1 F Results Obtained with the Circuit of Figure 2 at 5MHz. FFT Shows 81dB Overall Spurious Free Dynamic Range 5.023193MHz IN –10 ...
Page 13
... BSC 4.90 0.15 DETAIL “A” (1.93 .006) 0.254 (.010) 0 – 6 TYP 0.53 0.015 1.10 (.021 .006) (.043) DETAIL “A” MAX SEATING PLANE 0.22 – 0.38 (.009 – .015) TYP LT1818/LT1819 OUT 18189 SS 0.52 (.206 REF 3.00 0.102 (.118 .004) NOTE 0.86 (.034) REF 0.13 0.076 (.005 .003) ...
Page 14
... LT1818/LT1819 PACKAGE DESCRIPTIO 0.62 MAX 3.85 MAX 2.62 REF RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.20 BSC DATUM ‘A’ 0.35 – 0.55 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6 ...
Page 15
... TYP .016 – .050 .014 – .019 (0.406 – 1.270) (0.355 – 0.483) TYP INCHES (MILLIMETERS) LT1818/LT1819 .189 – .197 (4.801 – 5.004) NOTE .150 – .157 (3.810 – 3.988) NOTE 3 ...
Page 16
... LT1818/LT1819 U TYPICAL APPLICATIO 20dB Gain Block Frequency Response – –10 100k 1M 10M FREQUENCY (Hz) RELATED PARTS PART NUMBER DESCRIPTION LT1395/LT1396/LT1397 Single/Dual/Quad 400MHz Current Feedback Amplifiers LT1806/LT1807 Single/Dual 325MHz, 140V/ s Rail-to-Rail I/O Op Amps LT1809/LT1810 Single/Dual 180MHz, 350V/ s Rail-to-Rail I/O Op Amps ...
Page 17
... This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components. ...