LTC1471 LINER [Linear Technology], LTC1471 Datasheet
LTC1471
Available stocks
Related parts for LTC1471
LTC1471 Summary of contents
Page 1
... The output is limited to 1A during short circuit to ground but 2A of peak operating current is allowed. The LTC1471 is a dual version of the LTC1470 and is available in a 16-pin SO package. , LTC and LT are registered trademarks of Linear Technology Corporation. SafeSlot is a trademark of Linear Technology Corporation. ...
Page 2
... OUT Program to Hi- (Note 3) OUT Program to 3.3V (Note 4) OUT Program to 5V (Note 4) OUT ORDER PART TOP VIEW NUMBER 16 AOUT 15 A3V IN LTC1471CS 14 A3V IN 13 GND 12 BEN0 11 BEN1 10 B5V IN 9 BOUT S PACKAGE = 100 C unless otherwise noted. A MIN TYP MAX 2 ...
Page 3
... Note 1: For the LTC1470, the two output pins (1, 8) must be connected together and the two 3.3V supply input pins ( must be connected together. For the LTC1471, the two AOUT pins (1, 16) must be connected together, the two BOUT pins (8, 9) must be connected together, the two ...
Page 4
... Input Supply Pins. The 3V IN pins serve as the power supply input for the 3.3V switches. These pins do not provide any power to the internal control Enable CC circuitry and therefore do not consume any power when unloaded or turned off. (LTC1470 or 1/2 LTC1471) Inrush Current (5V Switch) 3 CURRENT 2 LIMITED 1 0 ...
Page 5
... FUNCTIONS LTC1471 AOUT, BOUT(Pins 1, 16, 8, 9): Output Pins. The outputs of the LTC1471 are switched between three operating states: OFF, 3.3V and 5V. These pins are protected against accidental short circuits to ground by SafeSlot current limit circuitry which protects the socket, the card, and the system power supplies against damage ...
Page 6
... LTC1470/LTC1471 U OPERATION The LTC1470 (or 1/2 of the LTC1471) consists of the following functional blocks: Input TTL/CMOS Converters The enable inputs are designed to accommodate a wide range of 3V and 5V logic families. The input threshold voltage is approximately 1.4V with approximately 100mV of hysteresis. The inputs enable the bias generator, the gate charge pumps and the protection circuity which are powered from the 5V supply ...
Page 7
... NMOS switch gates Hi-Z are fully discharged to 0V. Whenever possible, however best to leave the 5V LTC1470/LTC1471 quiescent current drops to <1 A with all the switches turned off and therefore no 5V power is consumed in the standby mode. LTC1470/LTC1471 supply pins (see graphs in Typical Perfor- IN pin(s) continuously powered ...
Page 8
... VPP power. And, because the LTC1470/LTC1471 do not require 12V power to operate (only 5V), the 12V VPP regulation and switching may be operated separately from the 3.3V/5V V switching. This increases system configuration flexibility and reduces total system cost by eliminating the need for a third regulator for 12V power ...
Page 9
... MBRS130T3 T1 100 1000pF 0.033 100 28 – 12k Q3 2N7002 Q4 2N7002 *CTX02-12753 COILTRONICS (407) 241-7876 LTC1470/LTC1471 pins of the LT1313. (See the LT1312 and OUT D2 MBRS1100 15V AUX SUPPLY 3.37 18V 68 F 3.3V OUTPUT C3 220 F 1470/71 F04 9 ...
Page 10
... SEE FIGURES 3, 4 FOR FURTHER DETAIL 10 (Systems with No 12V Power Requirements) 0.1 F A3V A3V B3V B3V A5V BOUT IN (OFF/3.3V/5V) 0.1 F B5V BOUT TANT LTC1471 AEN0 AEN1 BEN0 AOUT (OFF/3.3V/5V) BEN1 AOUT + GND GND 1 F TANT 13V TO 20V* 51k V S EN0 VPP OUT + EN1 LT1312 ...
Page 11
... A3V B3V B3V A5V 5V BOUT IN 0.1 F B5V BOUT IN LTC1471 AEN0 AEN1 BEN0 AOUT BEN1 AOUT GND GND LTC1470/LTC1471 0.1 F VPP1 VPP2 PCMCIA CARD SLOT VPP1 VPP2 PCMCIA PCMCIA CARD SLOT CARD SLOT (OFF/3.3V/5V 10k TANT (OFF/3 ...
Page 12
... LTC1470/LTC1471 PACKAGE DESCRIPTION 0.010 – 0.020 45 (0.254 – 0.508) 0.008 – 0.010 0 – 8 TYP (0.203 – 0.254) 0.016 – 0.050 0.406 – 1.270 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm). 0.010 – 0.020 45 (0.254 – ...