BCCM6033SQ Cooper/Bussmann, BCCM6033SQ Datasheet - Page 216

• Manufacturer Part Number: BCCM6033SQ
• Description: FUSEBLOCK CLASS CC 13/32X1-1/2"
• Manufacturer: Cooper/Bussmann
• Series: BCCMr
• Type: Blockr

Specifications of BCCM6033SQ

• Fuse Size: Class CC
• Number Of Circuits: 3
• Mounting Type: Chassis Mount
• Termination Style: Screw Terminal
• Current Rating: 20A
• Product: Block
• Fuse Size / Group: Class CC
• Voltage Rating: 600 Volts
• Mounting Style: Screw
• Body Material: Thermoplastic
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Operating Principles of Bussmann
The principles of operation of the modern, current-limiting Buss
fuses are covered in the following paragraphs.
Non-Time-Delay Fuses
The basic component of a fuse is the link. Depending upon the
ampere rating of the fuse, the single-element fuse may have one
or more links. They are electrically connected to the end blades (or
ferrules) (see Figure 1) and enclosed in a tube or cartridge sur-
rounded by an arc quenching filler material. BUSS
and T-TRON
Under normal operation, when the fuse is operating at or near its
ampere rating, it simply functions as a conductor. However, as
illustrated in Figure 2, if an overload current occurs and persists for
more than a short interval of time, the temperature of the link even-
tually reaches a level which causes a restricted segment of the link
to melt. As a result, a gap is formed and an electric arc estab-
lished. However, as the arc causes the link metal to burn back, the
gap becomes progressively larger. Electrical resistance of the arc
eventually reaches such a high level that the arc cannot be sus-
tained and is extinguished. The fuse will have then completely cut
off all current flow in the circuit. Suppression or quenching of the
arc is accelerated by the filler material. (See Figure 3.)
Single-element fuses of present day design have a very high
speed of response to overcurrents. They provide excellent short-
circuit component protection. However, temporary, harmless
overloads or surge currents may cause nuisance openings unless
these fuses are oversized. They are best used, therefore, in cir-
cuits not subject to heavy transient surge currents and the tem-
porary over-load of circuits with inductive loads such as motors,
transformers, solenoids, etc. Because single-element, fast-acting
fuses such as LIMITRON and T-TRON fuses have a high speed of
response to short-circuit currents, they are particularly suited for
the protection of circuit breakers with low interrupting ratings.
Whereas an overload current normally falls between one and
six times normal current, short-circuit currents are quite high.
The fuse may be subjected to short-circuit currents of 30,000
or 40,000A or higher. Response of current limiting fuses to such
currents is extremely fast. The restricted sections of the fuse link
will simultaneously melt (within a matter of two or three-thou-
sandths of a second in the event of a high-level fault current).
The high total resistance of the multiple arcs, together with the
quenching effects of the filler particles, results in rapid arc sup-
pression and clearing of the circuit. (Refer to Figures 4 & 5) Short-
circuit current is cut off in less than a half-cycle, long before the
short-circuit current can reach its full value (fuse operating in its
current limiting range).
212
Fuse Technology
®
fuses are both single-element fuses.
®
Fuses
®
LIMITRON
®
Figure 1. Cutaway view of typical single-element fuse.
Figure 2. Under sustained overload, a section of the link melts and an
arc is established.
Figure 3. The “open” single-element fuse after opening a circuit
overload.
Figure 4. When subjected to a short-circuit current, several
sections of the fuse link melt almost instantly.
Figure 5. The “open” single-element fuse after opening a short circuit.
Bussmann
®