PIC16C620A-20/P Microchip Technology, PIC16C620A-20/P Datasheet - Page 62

• Manufacturer Part Number: PIC16C620A-20/P
• Description: IC MCU OTP 512X14 COMP 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C620A-20/P

• Core Size: 8-Bit
• Program Memory Size: 896B (512 x 14)
• Oscillator Type: External
• Core Processor: PIC
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 13
• Program Memory Type: OTP
• Ram Size: 96 x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16C
• No. Of I/o's: 13
• Ram Memory Size: 128Byte
• Cpu Speed: 20MHz
• No. Of Timers: 1
• Digital Ic: RoHS Compliant
• Processor Series: PIC16C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 96 B
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 13
• Number Of Timers: 8
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000, DM163022
• Minimum Operating Temperature: 0 C
• Data Rom Size: 96 B
• Height: 3.3 mm
• Length: 22.86 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 3 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMING309-1059 - ADAPTER 18 ZIF BD W/18SO PLUGSDVA16XP180 - ADAPTER DEVICE FOR MPLAB-ICEAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Eeprom Size: -
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Details

PIC16C62X
9.9
If
programmed, the on-chip program memory can be
read out for verification purposes.
9.10
Four memory locations (2000h-2003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution, but are
readable and writable during Program/Verify. Only the
Least Significant 4 bits of the ID locations are used.
DS30235J-page 60
Note:
the
Code Protection
ID Locations
code
Microchip does not recommend code
protecting windowed devices.
protection
bit(s)
have
not
been
9.11
The PIC16C62X microcontrollers can be serially
programmed while in the end application circuit. This is
simply done with two lines for clock and data and three
other lines for power, ground and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices and then program the
microcontroller just before shipping the product. This
also allows the most recent firmware or a custom
firmware to be programmed.
The device is placed into a Program/Verify mode by
holding the RB6 and RB7 pins low, while raising the
MCLR (V
specification). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After RESET, to place the device into Programming/
Verify mode, the program counter (PC) is at location
00h. A 6-bit command is then supplied to the device.
Depending on the command, 14-bits of program data
are then supplied to or from the device, depending if
the command was a load or a read. For complete
details of serial programming, please refer to the
PIC16C6X/7X/9XX
(DS30228).
A typical In-Circuit Serial Programming connection is
shown in Figure 9-19.
FIGURE 9-19:
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
In-Circuit Serial Programming™
PP
PP
) pin from V
To Normal
Connections
To Normal
Connections
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
Programming
 2003 Microchip Technology Inc.
IL
to V
IHH
(see programming
V
V
MCLR/V
RB6
RB7
V
PIC16C62X
DD
SS
DD
Specification
PP