PIC12CE673-04/P Microchip Technology, PIC12CE673-04/P Datasheet - Page 579

• Manufacturer Part Number: PIC12CE673-04/P
• Description: IC MCU OTP 1KX14 A/D&EE 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Cr

Specifications of PIC12CE673-04/P

• Core Size: 8-Bit
• Program Memory Size: 1.75KB (1K x 14)
• Core Processor: PIC
• Speed: 4MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Program Memory Type: OTP
• Eeprom Size: 16 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 4x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Controller Family/series: PIC12
• No. Of I/o's: 6
• Eeprom Memory Size: 16Byte
• Ram Memory Size: 128Byte
• Cpu Speed: 4MHz
• No. Of Timers: 1
• Processor Series: PIC12C
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Maximum Clock Frequency: 4 MHz
• Number Of Programmable I/os: 5
• Number Of Timers: 8
• Maximum Operating Temperature: + 70 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: ICE2000
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ISPICR1 - ADAPTER IN-CIRCUIT PROGRAMMINGAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Details

30.6
DC CHARACTERISTICS
D030
D030A
D031
D032
D033
D040
D040A
D041
D042
D042A
D043
D050
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
Param
1997 Microchip Technology Inc.
No.
† Data in “Typ” column is at 5V, 25 C unless otherwise stated. These parameters are for design guidance only
2: Not Applicable.
3: Not Applicable.
4: The better of the two specifications may be used. For V
and are not tested.
PICmicro be driven with an external clock while in RC mode.
would be the lower voltage.
Symbol
V
Input Threshold Levels
V
V
HYS
IH
IL
Input Low Voltage
I/O ports:
MCLR, OSC1 (RC mode)
OSC1
(XT, HS and LP modes)
Input High Voltage
MCLR
OSC1
(XT, HS and LP modes)
OSC1 (RC mode)
Hysteresis of Schmitt Trigger
Inputs
with Schmitt Trigger buffer
with TTL buffer
with Schmitt Trigger buffer
I/O ports:
with TTL buffer
The Input Low Voltage (V
read a ’0’ at a voltage level above this. All designs should be to the specification since device to
device (and to a much lesser extent pin to pin) variations will cause this level to vary.
The Input High Voltage (V
read a ’1’ at a voltage level below this. All designs should be to the specification since device to
device (and to a much lesser extent pin to pin) variations will cause this level to vary.
The I/O pins with TTL levels are shown with two specifications. One is the industry standard TTL
specification, which is specified for the voltage range of 4.5V to 5.5V. The other is a specification
that operates over the entire voltage range of the device. The better of these two specifications
may be used in the design.
Table 30-6:
Section 30. Electrical Specifications
Characteristic
Example DC Characteristics
(1)
(1)
IL
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Operating voltage V
IH
) is the voltage level that will be read as a logic ’0’. An input may not
0.25V
) is the voltage level that will be read as a logic ’1’. An input may
0.8V
0.7V
0.8V
0.9V
+ 0.8V
TBD
Min
V
V
V
V
2.0
—
SS
SS
SS
SS
DD
DD
DD
DD
DD
Typ†
—
—
—
—
—
—
—
—
—
—
—
—
IL
this would be the higher voltage and for V
DD
0.15V
0.2V
0.2V
0.3V
Max
V
V
V
V
V
V
0.8
range as described in DC spec
—
DD
DD
DD
DD
DD
DD
DD
DD
DD
0˚C
-40˚C
-40˚C
DD
Units
V
V
V
V
V
V
V
V
V
V
V
V
T
T
T
A
A
A
For entire V
4.5V
For entire V
For entire V
4.5V
For entire V
+70˚C for commercial,
+85˚C for industrial and
+125˚C for extended
V
V
Conditions
DD
DD
DS31030A-page 30-9
DD
DD
DD
DD
5.5V
5.5V
range
range
range
range
Table
(4)
(4)
IH
(4)
(4)
30-3.
this
30