PIC18F24J11-I/SP Microchip Technology, PIC18F24J11-I/SP Datasheet - Page 181
![IC PIC MCU FLASH 16KB 28-DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC18F24J11-I/SP
Manufacturer Part Number
PIC18F24J11-I/SP
Description
IC PIC MCU FLASH 16KB 28-DIP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.MA180023.pdf
(528 pages)
2.PIC18LF24J10-ISS.pdf
(32 pages)
3.PIC18F24J11-ISS.pdf
(14 pages)
Specifications of PIC18F24J11-I/SP
Core Size
8-Bit
Program Memory Size
16KB (8K x 16)
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
16
Program Memory Type
FLASH
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
2.15 V ~ 3.6 V
Data Converters
A/D 10x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Controller Family/series
PIC18
No. Of I/o's
16
Ram Memory Size
3.6875KB
Cpu Speed
48MHz
No. Of Timers
5
Interface
EUSART, I2C, SPI
Embedded Interface Type
EUSART, I2C, SPI
Rohs Compliant
Yes
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
3776 B
Interface Type
EUSART, I2C, SPI
Maximum Clock Frequency
48 MHz
Number Of Timers
5
Maximum Operating Temperature
+ 85 C
Mounting Style
Through Hole
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DM183033, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 10 Channel
Package
28SPDIP
Device Core
PIC
Family Name
PIC18
Maximum Speed
48 MHz
Operating Supply Voltage
2.5|3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC162067 - HEADER INTRFC MPLAB ICD2 40/28PAC164329 - MODULE SKT FOR 40DIP 18F45J10
Eeprom Size
-
Lead Free Status / Rohs Status
Details
- Current page: 181 of 528
- Download datasheet (8Mb)
10.3.5
Up to two chip select lines, PMCS1 and PMCS2, are
available for the Master modes of the PMP. The two
chip select lines are multiplexed with the Most Signifi-
cant bit (MSb) of the address bus (PMADDRH<6>).
When a pin is configured as a chip select, it is not
included in any address auto-increment/decrement.
The function of the chip select signals is configured
using the chip select function bits (PMCONL<7:6>).
10.3.6
While the module is operating in one of the Master
modes, the INCMx bits (PMMODEH<4:3>) control the
behavior of the address value. The address can be
made to automatically increment or decrement after
each read and write operation. The address increments
once each operation is completed and the BUSY bit
goes to ‘0’. If the chip select signals are disabled and
configured as address bits, the bits will participate in
the increment and decrement operations; otherwise,
the CS1 bit values will be unaffected.
10.3.7
In Master mode, the user has control over the duration
of the read, write and address cycles by configuring the
module Wait states. Three portions of the cycle, the
beginning, middle and end, are configured using the
corresponding WAITBx, WAITMx and WAITEx bits in
the PMMODEL register.
The WAITBx bits (PMMODEL<7:6>) set the number of
Wait cycles for the data setup prior to the
PMRD/PMWT strobe in Mode 10, or prior to the
PMENB strobe in Mode 11. The WAITMx bits
(PMMODEL<5:2>) set the number of Wait cycles for
the PMRD/PMWT strobe in Mode 10, or for the PMENB
strobe in Mode 11. When this Wait state setting is ‘0’,
then WAITB and WAITE have no effect. The WAITE
bits (PMMODEL<1:0>) define the number of Wait
cycles for the data hold time after the PMRD/PMWT
strobe in Mode 10, or after the PMENB strobe in
Mode 11.
10.3.8
To perform a read on the PMP, the user reads the
PMDIN1L register. This causes the PMP to output the
desired values on the chip select lines and the address
bus. Then the read line (PMRD) is strobed. The read
data is placed into the PMDIN1L register.
If the 16-bit mode is enabled (MODE16 = 1), the read
of the low byte of the PMDIN1L register will initiate two
bus reads. The first read data byte is placed into the
PMDIN1L register, and the second read data is placed
into the PMDIN1H.
© 2009 Microchip Technology Inc.
WAIT STATES
CHIP SELECT FEATURES
AUTO-INCREMENT/DECREMENT
READ OPERATION
PIC18F46J11 FAMILY
Note that the read data obtained from the PMDIN1L
register is actually the read value from the previous
read operation. Hence, the first user read will be a
dummy read to initiate the first bus read and fill the read
register. Also, the requested read value will not be
ready until after the BUSY bit is observed low. Thus, in
a back-to-back read operation, the data read from the
register will be the same for both reads. The next read
of the register will yield the new value.
10.3.9
To perform a write onto the parallel bus, the user writes
to the PMDIN1L register. This causes the module to
first output the desired values on the chip select lines
and the address bus. The write data from the PMDIN1L
register is placed onto the PMD<7:0> data bus. Then
the write line (PMWR) is strobed. If the 16-bit mode is
enabled (MODE16 = 1), the write to the PMDIN1L
register will initiate two bus writes. First write will
consist of the data contained in PMDIN1L and the
second write will contain the PMDIN1H.
10.3.10
10.3.10.1
In addition to the PMP interrupt, a BUSY bit is provided
to indicate the status of the module. This bit is used
only in Master mode. While any read or write operation
is in progress, the BUSY bit is set for all but the very last
CPU cycle of the operation. In effect, if a single-cycle
read or write operation is requested, the BUSY bit will
never be active. This allows back-to-back transfers.
While the bit is set, any request by the user to initiate a
new operation will be ignored (i.e., writing or reading
the lower byte of the PMDIN1L register will neither
initiate a read nor a write).
10.3.10.2
When the PMP module interrupt is enabled for Master
mode, the module will interrupt on every completed
read or write cycle; otherwise, the BUSY bit is available
to query the status of the module.
WRITE OPERATION
PARALLEL MASTER PORT STATUS
The BUSY Bit
Interrupts
DS39932C-page 181
Related parts for PIC18F24J11-I/SP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![TC1014-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1014-5.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.7VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-2.8VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1055-4.0VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.5VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet:
![TC1186-2.85VCT](/images/manufacturer_photos/0/4/440/microchip_technology_inc__tmb.jpg)
Part Number:
Description:
Manufacturer:
Microchip Technology Inc.
Datasheet: