PIC18F26K20-E/SS Microchip Technology, PIC18F26K20-E/SS Datasheet - Page 3
![IC PIC MCU FLASH 32KX16 28SSOP](/photos/6/81/68119/150-28-ssop_sml.jpg)
PIC18F26K20-E/SS
Manufacturer Part Number
PIC18F26K20-E/SS
Description
IC PIC MCU FLASH 32KX16 28SSOP
Manufacturer
Microchip Technology
Series
PIC® XLP™ 18Fr
Datasheets
1.PIC18F25K20T-ISS.pdf
(42 pages)
2.PIC18F25K20T-ISS.pdf
(456 pages)
3.PIC18F26K20-ISS.pdf
(6 pages)
4.PIC18F26K20-ISS.pdf
(10 pages)
5.PIC18F26K20-EML.pdf
(430 pages)
Specifications of PIC18F26K20-E/SS
Core Size
8-Bit
Program Memory Size
64KB (32K x 16)
Core Processor
PIC
Speed
48MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, HLVD, POR, PWM, WDT
Number Of I /o
24
Program Memory Type
FLASH
Eeprom Size
1K x 8
Ram Size
3.8K x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 3.6 V
Data Converters
A/D 11x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 125°C
Package / Case
28-SSOP
Controller Family/series
PIC18
No. Of I/o's
25
Eeprom Memory Size
1024Byte
Ram Memory Size
3.84375KB
Cpu Speed
64MHz
No. Of Timers
4
Processor Series
PIC18F
Core
PIC
Data Bus Width
8 bit
Data Ram Size
3936 B
Interface Type
CCP, ECCP, EUSART, I2C, MSSP, SPI
Maximum Clock Frequency
64 MHz
Number Of Programmable I/os
25
Number Of Timers
4
Maximum Operating Temperature
+ 125 C
Mounting Style
SMD/SMT
3rd Party Development Tools
52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
Development Tools By Supplier
PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
Minimum Operating Temperature
- 40 C
On-chip Adc
10 bit, 11 Channel
Package
28SSOP
Device Core
PIC
Family Name
PIC18
Maximum Speed
64 MHz
Operating Supply Voltage
2.5|3.3 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPAC164307 - MODULE SKT FOR PM3 28SSOP
Lead Free Status / Rohs Status
Details
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F26K20-E/SS
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Silicon Errata Issues
1. Module: ECCP
2. Module: ECCP
2010 Microchip Technology Inc.
Note:
Changing direction in Full-Bridge mode inserts a
dead band time of 4/F
instead of 1/F
the data sheet.
Work around
None.
Affected Silicon Revisions
ECCP
PR2 = CCPR1L and DC1B[1:0] <>'00' and the
direction is changed, then the dead time before the
modulated output starts is compromised. The
modulated signal improperly starts immediately
with the direction change and stays on for
T
Work around
Avoid changing direction when the duty cycle is
within three least significant steps of 100% duty
cycle. Instead, clear the DC1B[1:0] bits before the
direction change and then set them to the desired
value after the direction change is complete.
Affected Silicon Revisions
OSC
B2
B2
X
X
* TMR2Presale * DC1B[1:0].
This document summarizes all silicon
errata issues from all revisions of silicon,
previous as well as current. Only the
issues indicated by the shaded column in
the following tables apply to the current
silicon revision (B5).
B3
B3
X
X
–
OSC
B5
B5
X
X
In
* TMR2 prescale as specified in
Full-Bridge
OSC
* TMR2 prescale
mode
when
3. Module: MSSP SPI
4. Module: MSSP SPI
5. Module: MSSP (Master I
PIC18F26K20/46K20
When the SPI clock is configured for Timer2/2
(SSPCON1<3:0> = 0011) and the CKE bit of the
SSPSTAT register is ‘1’, then the first SDO data bit
and SCK non-idle edge occur simultaneously.
Also, the first SCK non-idle level may be short.
Work around
Use clock mode other than Timer2/2.
Affected Silicon Revisions
In SPI Master mode, when the CKE bit of the
SSPSTAT register is cleared and the SMP bit of
the SSPSTAT register is set, then the last bit of the
incoming data stream (bit 0) at the SDI pin will not
be sampled properly.
Work around
None.
Affected Silicon Revisions
In Master I
occurs in the middle of an address or data
reception, then the SCL clock stream will continue
endlessly and the RCEN bit of the SSPCON2
register will remain set improperly. When a Start
condition occurs after the improper Stop condition,
then 9 additional clocks will be generated followed
by the RCEN bit going low.
Work around
Use low-impedance pull-ups on the SDA line to
reduce the possibility of noise glitches, which may
trigger an improper Stop event. Use a time-out
event timer to detect the unexpected Stop condi-
tion and resulting stuck RCEN bit. Clear stuck
RCEN bit by clearing SSPEN bit of SSPCON1.
Affected Silicon Revisions
B2
B2
B2
X
X
X
B3
B3
B3
X
X
X
2
C Receive mode, if a Stop condition
B5
B5
B5
X
X
X
2
C™ Mode)
DS80404E-page 3