PIC18F1220-I/P Microchip Technology, PIC18F1220-I/P Datasheet - Page 143

• Manufacturer Part Number: PIC18F1220-I/P
• Description: IC MCU FLASH 2KX16 A/D 18-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F1220-I/P

• Program Memory Type: FLASH
• Program Memory Size: 4KB (2K x 16)
• Package / Case: 18-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 16
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: EUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 7-ch x 10-bit
• Package: 18PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP180 - DEVICE ADAPTER 18F1320 PDIP 18LDACICE0202 - ADAPTER MPLABICE 18P 300 MILAC164010 - MODULE SKT PROMATEII DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

To set up an Asynchronous Transmission:
1.
2.
3.
4.
FIGURE 16-2:
FIGURE 16-3:
 2004 Microchip Technology Inc.
Reg. Empty Flag)
Reg. Empty Flag)
Write to TXREG
(Transmit Buffer
Initialize the SPBRGH:SPBRG registers for the
appropriate baud rate. Set or clear the BRGH
and BRG16 bits, as required, to achieve the
desired baud rate.
Enable the asynchronous serial port by clearing
bit SYNC and setting bit SPEN.
If interrupts are desired, set enable bit TXIE.
If 9-bit transmission is desired, set transmit bit
TX9. Can be used as address/data bit.
(Transmit Shift
CK/INT1 (pin)
RB1/AN5/TX/
BRG Output
(Shift Clock)
BRG16
TRMT bit
TXIF bit
TXIE
Interrupt
SPBRGH
Baud Rate Generator
TXIF
TXEN
EUSART TRANSMIT BLOCK DIAGRAM
ASYNCHRONOUS TRANSMISSION
Word 1
Transmit Shift Reg
Word 1
Baud Rate CLK
SPBRG
1 T
CY
Start bit
MSb
(8)
TX9D
TXREG Register
bit 0
TSR Register
TX9
8
Data Bus
bit 1
Word 1
5.
6.
7.
If using interrupts, ensure that the GIE and PEIE bits in
the INTCON register (INTCON<7:6>) are set.
Enable the transmission by setting bit TXEN,
which will also set bit TXIF.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit TX9D.
Load data to the TXREG register (starts
transmission).
LSb
0
PIC18F1220/1320
TRMT
and Control
Pin Buffer
bit 7/8
SPEN
RB1/AN5/TX/CK/INT1 pin
Stop bit
DS39605C-page 141