PIC24FJ64GA104-I/PT Microchip Technology, PIC24FJ64GA104-I/PT Datasheet - Page 173

• Manufacturer Part Number: PIC24FJ64GA104-I/PT
• Description: IC PIC MCU FLASH 64KB 44-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ64GA104-I/PT

• Core Size: 16-Bit
• Program Memory Size: 64KB (22K x 24)
• Core Processor: PIC
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Controller Family/series: PIC24
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Interface: I2C, LIN, SPI, USART
• No. Of Pwm Channels: 5
• Embedded Interface Type: I2C, LIN, SPI, USART
• Rohs Compliant: Yes
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, IrDA, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM240001, MA240020, DM240002, DM240011, DV164033
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 13 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARD
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

16.0
The Inter-Integrated Circuit (I
interface useful for communicating with other peripheral
or microcontroller devices. These peripheral devices
may be serial EEPROMs, display drivers, A/D
Converters, etc.
The I
• Independent master and slave logic
• 7-bit and 10-bit device addresses
• General call address as defined in the I
• Clock stretching to provide delays for the
• Both 100 kHz and 400 kHz bus specifications.
• Configurable address masking
• Multi-Master modes to prevent loss of messages
• Bus Repeater mode, allowing the acceptance of
• Automatic SCL
A block diagram of the module is shown in Figure 16-1.
© 2009 Microchip Technology Inc.
Note:
processor to respond to a slave data request
in arbitration
all messages as a slave regardless of the address
2
C module supports these features:
INTER-INTEGRATED CIRCUIT
(I
2
This data sheet summarizes the features
of this group of PIC24F devices. It is not
intended to be a comprehensive reference
source. For more information, refer to the
“PIC24F
Section 24. “Inter-Integrated Circuit™
(I
C™)
2
C™)” (DS39702).
Family
2
C) module is a serial
Reference
2
C protocol
Manual”,
PIC24FJ64GA104 FAMILY
Preliminary
16.1
The details of sending a message in Master mode
depends on the communications protocol for the device
being communicated with. Typically, the sequence of
events is as follows:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Wait for and verify an Acknowledge from the
11. Enable master reception to receive serial
12. Generate an ACK or NACK condition at the end
13. Generate a Stop condition on SDAx and SCLx.
Assert a Start condition on SDAx and SCLx.
Send the I
with a write indication.
Wait for and verify an Acknowledge from the
slave.
Send the first data byte (sometimes known as
the command) to the slave.
Wait for and verify an Acknowledge from the
slave.
Send the serial memory address low byte to the
slave.
Repeat steps 4 and 5 until all data bytes are
sent.
Assert a Repeated Start condition on SDAx and
SCLx.
Send the device address byte to the slave with
a read indication.
slave.
memory data.
of a received byte of data.
Communicating as a Master in a
Single Master Environment
2
C device address byte to the slave
DS39951B-page 171