PIC18F87J90-I/PT Microchip Technology, PIC18F87J90-I/PT Datasheet - Page 248

• Manufacturer Part Number: PIC18F87J90-I/PT
• Description: IC PIC MCU FLASH 128KB 80-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F87J90-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, LVD, POR, PWM, WDT
• Number Of I /o: 67
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3923 B
• Interface Type: AUSART, EUSART, I2C, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 67
• Number Of Timers: 4
• Operating Supply Voltage: 2.65 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 12 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162079 - HEADER MPLAB ICD2 18F85J90 64/80AC164323 - MODULE SKT FOR 100TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F87J90 FAMILY
18.4.12
An Acknowledge sequence is enabled by setting the
Acknowledge
(SSPCON2<4>). When this bit is set, the SCL pin is
pulled low and the contents of the Acknowledge data bit
are presented on the SDA pin. If the user wishes to gen-
erate an Acknowledge, then the ACKDT bit should be
cleared. If not, the user should set the ACKDT bit before
starting an Acknowledge sequence. The Baud Rate
Generator then counts for one rollover period (T
and the SCL pin is deasserted (pulled high). When the
SCL pin is sampled high (clock arbitration), the Baud
Rate Generator counts for T
pulled low. Following this, the ACKEN bit is automatically
cleared, the Baud Rate Generator is turned off and the
MSSP module then goes into Idle mode (Figure 18-25).
18.4.12.1
If the user writes the SSPBUF when an Acknowledge
sequence is in progress, then WCOL is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
FIGURE 18-25:
FIGURE 18-26:
DS39933D-page 248
ACKNOWLEDGE SEQUENCE
TIMING
WCOL Status Flag
Note: T
SCL
SDA
Sequence
SSPIF
Note: T
SDA
SCL
Write to SSPCON2,
Falling edge of
Acknowledge sequence starts here,
BRG
ACKNOWLEDGE SEQUENCE WAVEFORM
BRG
STOP CONDITION RECEIVE OR TRANSMIT MODE
9th clock
= one Baud Rate Generator period.
= one Baud Rate Generator period.
ACK
BRG
the end of receive
set PEN
Enable
ACKEN = 1, ACKDT = 0
. The SCL pin is then
SSPIF set at
write to SSPCON2,
bit,
D0
8
T
T
BRG
BRG
SDA asserted low before rising edge of clock
to setup Stop condition
ACKEN
BRG
T
SCL brought high after T
BRG
)
Cleared in
software
T
BRG
P
ACK
SCL = 1 for T
after SDA sampled high. P bit (SSPSTAT<4>) is set.
T
BRG
18.4.13
A Stop bit is asserted on the SDA pin at the end of a
receive/transmit by setting the Stop Sequence Enable
bit,
receive/transmit, the SCL line is held low after the fall-
ing edge of the ninth clock. When the PEN bit is set, the
master will assert the SDA line low. When the SDA line
is sampled low, the Baud Rate Generator is reloaded
and counts down to 0. When the Baud Rate Generator
times out, the SCL pin will be brought high and one
T
SDA pin will be deasserted. When the SDA pin is
sampled high while SCL is high, the P bit
(SSPSTAT<4>) is set. A T
cleared and the SSPIF bit is set (Figure 18-26).
18.4.13.1
If the user writes the SSPBUF when a Stop sequence
is in progress, then the WCOL bit is set and the
contents of the buffer are unchanged (the write doesn’t
occur).
BRG
T
BRG
9
SSPIF set at the end
of Acknowledge sequence
PEN
(Baud Rate Generator rollover count) later, the
PEN bit (SSPCON2<2>) is cleared by
hardware and the SSPIF bit is set
BRG
BRG
, followed by SDA = 1 for T
STOP CONDITION TIMING
(SSPCON2<2>).
ACKEN automatically cleared
WCOL Status Flag
Cleared in
software
 2010 Microchip Technology Inc.
BRG
At
BRG
later, the PEN bit is
the
end
of
a