PIC18F6410-I/PT Microchip Technology, PIC18F6410-I/PT Datasheet - Page 250

• Manufacturer Part Number: PIC18F6410-I/PT
• Description: IC PIC MCU FLASH 8KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6410-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI/I2C/EUSART/AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
19.3
The Synchronous Master mode is entered by setting
the CSRC bit (TXSTA2<7>). In this mode, the data is
transmitted in a half-duplex manner (i.e., transmission
and reception do not occur at the same time). When
transmitting data, the reception is inhibited and vice
versa. Synchronous mode is entered by setting bit,
SYNC (TXSTA2<4>). In addition, enable bit, SPEN
(RCSTA2<7>), is set in order to configure the TX2 and
RX2 pins to CK2 (clock) and DT2 (data) lines,
respectively.
The Master mode indicates that the processor transmits
the master clock on the CK2 line.
19.3.1
The AUSART transmitter block diagram is shown in
Figure
(Serial) Shift register (TSR). The Shift register obtains
its data from the Read/Write Transmit Buffer register,
TXREG2. The TXREG2 register is loaded with data in
software. The TSR register is not loaded until the last
bit has been transmitted from the previous load. As
soon as the last bit is transmitted, the TSR is loaded
with new data from the TXREG2 (if available).
FIGURE 19-6:
DS39635C-page 250
RX2/DT2 Pin
TX2/CK2 Pin
Write to
TXREG2 Reg
TX2IF bit
(Interrupt Flag)
TRMT bit
TXEN bit
Note: Sync Master mode, SPBRG2 = 0, continuous transmission of two 8-bit words.
19-1. The heart of the transmitter is the Transmit
AUSART Synchronous
Master Mode
AUSART SYNCHRONOUS MASTER
TRANSMISSION
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
‘1’
Write Word 1
SYNCHRONOUS TRANSMISSION
bit 0
Write Word 2
bit 1
Word 1
bit 2
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Once the TXREG2 register transfers the data to the
TSR register (occurs in one T
empty and the TX2IF flag bit (PIR3<4>) is set. The
interrupt can be enabled or disabled by setting or clear-
ing the interrupt enable bit, TX2IE (PIE3<4>). TX2IF is
set regardless of the state of enable bit, TX2IE; it can-
not be cleared in software. It will reset only when new
data is loaded into the TXREG2 register.
While flag bit, TX2IF, indicates the status of the TXREG2
register, another bit, TRMT (TXSTA2<1>), shows the
status of the TSR register. TRMT is a read-only bit which
is set when the TSR is empty. No interrupt logic is tied to
this bit so the user has to poll this bit in order to deter-
mine if the TSR register is empty. The TSR is not
mapped in data memory so it is not available to the user.
To set up a Synchronous Master Transmission:
1.
2.
3.
4.
5.
6.
7.
8.
bit 7
Initialize the SPBRG2 register for the appropriate
baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
If interrupts are desired, set enable bit, TX2IE.
If 9-bit transmission is desired, set bit, TX9.
Enable the transmission by setting bit, TXEN.
If 9-bit transmission is selected, the ninth bit
should be loaded in bit, TX9D.
Start transmission by loading data to the
TXREG2 register.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
bit 0
Word 2
bit 1
 2010 Microchip Technology Inc.
CYCLE
), the TXREG2 is
bit 7
‘1’