DSPIC30F3014-30I/P Microchip Technology, DSPIC30F3014-30I/P Datasheet
![IC DSPIC MCU/DSP 24K 40DIP](/photos/6/61/66192/150-40-dip_sml.jpg)
DSPIC30F3014-30I/P
Specifications of DSPIC30F3014-30I/P
Available stocks
Related parts for DSPIC30F3014-30I/P
DSPIC30F3014-30I/P Summary of contents
Page 1
... Rev. A2 Silicon Errata The dsPIC30F3014/4013 (Rev. A2) samples that you have received were found to conform to the specifications and functionality described in the following documents: • DS70157 – “dsPIC30F/33F Programmer’s Reference Manual” • DS70138 – “dsPIC30F3014/4013 Data Sheet” • DS70046 – “dsPIC30F Family Reference Manual” ...
Page 2
... PLL Mode If 8x PLL mode is used, the input frequency range is 5 MHz-10 MHz instead of 4 MHz-10 MHz. 16. Low-Voltage Detect (LVD) The external Low-Voltage Detect (LVD) module is not connected to the AN2 Pad. 17. I/O Port – Port Pin Multiplexed with IC1 ...
Page 3
... MAC class instructions not use the + = address modification not prefetch data from Y data space. © 2008 Microchip Technology Inc. dsPIC30F3014/4013 2. Module: CPU – Instruction DAW.b The Decimal Adjust instruction, DAW.b, may improperly clear the Carry bit, C (SR<0>), when executed ...
Page 4
... Table 1. The work around for Example 2 is demonstrated in Example 3. DS80397A-page 4 These instructions are identified in Table 1. Example 2 demonstrates one scenario where this occurs. Also, always use Work around 2 if the C compiler is used to generate code for dsPIC30F3014/4013 devices. (1) (2) Examples of Incorrect Operation ADDC W0, [W1++], W2 ; SUBB.b W0, [++W1 ...
Page 5
... X; \ DISICNT = 0; } DISI_PROTECT(SRbits.IPL = 0x5); © 2008 Microchip Technology Inc. dsPIC30F3014/4013 Work around The user may disable interrupt nesting or execute a DISI instruction before modifying the CPU IPL or Interrupt 1 setting. A minimum DISI value required if the DISI is executed immediately before the CPU IPL or Interrupt 1 is modified, as shown in Example 4 ...
Page 6
... Module: DISI Instruction When a user executes a DISI #7, for example, this will disable interrupts from cycles (7 + the DISI instruction itself). In this case, the DISI instruction uses a counter which counts down from The counter is loaded with 7 at the end of the DISI instruction. ...
Page 7
... PORTF will be modified by a write to address 0x0E0 Work around User software should avoid writing to the unimplemented locations listed above. © 2008 Microchip Technology Inc. dsPIC30F3014/4013 12. Module: 4x PLL Operation When the 4x PLL mode of operation is selected, . the specified input frequency range of 4-10 MHz is CY not fully supported ...
Page 8
... Module: Low-Voltage Detect (LVD) When using the external Low-Voltage Detect (LVD) module, interrupts are independent of the voltage. Work around The LVD module works as an internal reference source only. 17. Module: I/O Port – Port Pin Multiplexed with IC1 If the user application enables the auto-baud ...
Page 9
... Clear the I C receiver interrupt flag SI2CF back to step 1 to continue receiving incoming data bytes. © 2008 Microchip Technology Inc. dsPIC30F3014/4013 Work around 2: Use this work around for applications in which the receiver interrupt is required. Assuming that the RBF and the I2COV flags in the I2CSTAT ...
Page 10
... Module there are two I C devices on the bus, one of them is acting as the Master receiver and the other as the Slave transmitter. If both devices are config- ured for 10-bit addressing mode, and have the same value in the A10 and A9 bits of their ...
Page 11
... APPENDIX A: REVISION HISTORY Revision A (9/2008) Initial version of this document. © 2008 Microchip Technology Inc. dsPIC30F3014/4013 DS80397A-page 11 ...
Page 12
... NOTES: DS80397A-page 12 © 2008 Microchip Technology Inc. ...
Page 13
... PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total Endurance, UNI/O, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. ...
Page 14
... Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan - Hsin Chu Tel: 886-3-572-9526 Fax: 886-3-572-6459 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-536-4803 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 © 2008 Microchip Technology Inc. 01/02/08 ...