PIC18F2455-I/SP Microchip Technology, PIC18F2455-I/SP Datasheet - Page 26

• Manufacturer Part Number: PIC18F2455-I/SP
• Description: IC PIC MCU FLASH 12KX16 28DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2455-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 24KB (12K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 24
• Eeprom Size: 256 x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: SPI/I2C/EAUSART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 4
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DM163014, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 48 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: I3-DB18F4550 - BOARD DAUGHTER ICEPIC3DM163025 - PIC DEM FULL SPEED USB DEMO BRDDVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2XXX/4XXX FAMILY
4.3
A configuration address may be read and output on
PGD via the 4-bit command, ‘1001’. Configuration data
is read and written in a byte-wise fashion, so it is not
necessary to merge two bytes into a word prior to a
compare. The result may then be immediately
compared to the appropriate configuration data in the
programmer’s memory for verification. Refer to
Section 4.1 “Read Code Memory, ID Locations and
Configuration Bits”
reading configuration data.
4.4
Data EEPROM is accessed, one byte at a time, via an
Address Pointer (register pair: EEADRH:EEADR) and
a data latch (EEDATA). Data EEPROM is read by load-
ing EEADRH:EEADR with the desired memory location
and initiating a memory read by appropriately configur-
ing the EECON1 register. The data will be loaded into
EEDATA, where it may be serially output on PGD via
the 4-bit command, ‘0010’ (Shift Out Data Holding
register). A delay of P6 must be introduced after the
falling edge of the 8th PGC of the operand to allow
PGD to transition from an input to an output. During this
time, PGC must be held low (see
The command sequence to read a single byte of data
is shown in
TABLE 4-2:
DS39622L-page 26
Step 1: Direct access to data EEPROM.
Step 2: Set the data EEPROM Address Pointer.
Step 3: Initiate a memory read.
Step 4: Load data into the Serial Data Holding register.
Note 1:
Command
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0010
4-Bit
Verify Configuration Bits
Read Data EEPROM Memory
The <LSB> is undefined. The <MSB> is the data.
Table
9E A6
9C A6
0E <Addr>
6E A9
OE <AddrH>
6E AA
80 A6
50 A8
6E F5
00 00
<MSB><LSB>
4-2.
READ DATA EEPROM MEMORY
Data Payload
for implementation details of
Figure
4-4).
BCF
BCF
MOVLW
MOVWF
MOVLW
MOVWF
BSF
MOVF
MOVWF
NOP
Shift Out Data
EECON1, EEPGD
EECON1, CFGS
<Addr>
EEADR
<AddrH>
EEADRH
EECON1, RD
EEDATA, W, 0
TABLAT
(1)
FIGURE 4-3:
Core Instruction
No
Move to TABLAT
Shift Out Data
READ DATA EEPROM
FLOW
 2010 Microchip Technology Inc.
Address
Done?
Read
Done
Start
Byte
Set
Yes