PIC16F84-04I/SO Microchip Technology, PIC16F84-04I/SO Datasheet - Page 52
![IC MCU FLASH 1KX14 EE 18SOIC](/photos/6/76/67656/150-18-soic_sml.jpg)
PIC16F84-04I/SO
Manufacturer Part Number
PIC16F84-04I/SO
Description
IC MCU FLASH 1KX14 EE 18SOIC
Manufacturer
Microchip Technology
Series
PIC® 16Fr
Datasheets
1.PIC16F688T-ISL.pdf
(688 pages)
2.PIC16LF84A-04P.pdf
(125 pages)
3.PIC16LF84A-04P.pdf
(4 pages)
Specifications of PIC16F84-04I/SO
Core Size
8-Bit
Program Memory Size
1.75KB (1K x 14)
Core Processor
PIC
Speed
4MHz
Peripherals
POR, WDT
Number Of I /o
13
Program Memory Type
FLASH
Eeprom Size
64 x 8
Ram Size
68 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
18-SOIC (7.5mm Width)
Controller Family/series
PIC16F
No. Of I/o's
13
Eeprom Memory Size
64Byte
Ram Memory Size
68Byte
Cpu Speed
4MHz
No. Of Timers
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
XLT18SO-1 - SOCKET TRANSITION 18SOIC 300MIL309-1075 - ADAPTER 18-SOIC TO 18-SOIC309-1011 - ADAPTER 18-SOIC TO 18-DIP309-1010 - ADAPTER 18-SOIC TO 18-DIPAC164010 - MODULE SKT PROMATEII DIP/SOIC
Data Converters
-
Connectivity
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
PIC16F8X
8.12
A device may be powered down (SLEEP) and later
powered up (Wake-up from SLEEP).
8.12.1
The Power-down mode is entered by executing the
SLEEP instruction.
If enabled, the Watchdog Timer is cleared (but keeps
running), the PD bit (STATUS<3>) is cleared, the TO bit
(STATUS<4>) is set, and the oscillator driver is turned
off. The I/O ports maintain the status they had before
the SLEEP instruction was executed (driving high, low,
or hi-impedance).
For the lowest current consumption in SLEEP mode,
place all I/O pins at either at V
external circuitry drawing current from the I/O pins, and
disable external clocks. I/O pins that are hi-impedance
inputs should be pulled high or low externally to avoid
switching currents caused by floating inputs. The
T0CKI input should also be at V
contribution from on-chip pull-ups on PORTB should be
considered.
The MCLR pin must be at a logic high level (V
It should be noted that a RESET generated by a WDT
time-out does not drive the MCLR pin low.
FIGURE 8-19: WAKE-UP FROM SLEEP THROUGH INTERRUPT
DS30430C-page 52
Note
INSTRUCTION FLOW
INTF flag
(INTCON<1>)
GIE bit
(INTCON<7>)
Instruction
fetched
CLKOUT(4)
Instruction
executed
INT pin
1: XT, HS or LP oscillator mode assumed.
2: T
3: GIE = ’1’ assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = ’0’, execution will continue in-line.
4: CLKOUT is not available in these osc modes, but shown here for timing reference.
OSC1
Power-down Mode (SLEEP)
SLEEP
PC
OST
Inst(PC) = SLEEP
Q1 Q2 Q3 Q4
= 1024T
Inst(PC - 1)
PC
OSC
(drawing not to scale) This delay will not be there for RC osc mode.
Q1 Q2 Q3 Q4
Inst(PC + 1)
SLEEP
PC+1
DD
DD
or V
or V
SS
Q1
Processor in
SLEEP
, with no
IHMC
SS
. The
PC+2
).
T
OST
(2)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Inst(PC + 2)
Inst(PC + 1)
8.12.2
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
Peripherals cannot generate interrupts during SLEEP,
since no on-chip Q clocks are present.
The first event (MCLR reset) will cause a device reset.
The two latter events are considered a continuation of
program execution. The TO and PD bits can be used to
determine the cause of a device reset. The PD bit,
which is set on power-up, is cleared when SLEEP is
invoked. The TO bit is cleared if a WDT time-out
occurred (and caused wake-up).
While the SLEEP instruction is being executed, the next
instruction (PC + 1) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up
occurs regardless of the state of the GIE bit. If the GIE
bit is clear (disabled), the device continues execution at
the instruction after the SLEEP instruction. If the GIE bit
is set (enabled), the device executes the instruction
after the SLEEP instruction and then branches to the
interrupt address (0004h). In cases where the
execution of the instruction following SLEEP
desirable, the user should have a NOP after the
SLEEP instruction.
PC+2
External reset input on MCLR pin.
WDT Wake-up (if WDT was enabled).
Interrupt from RB0/INT pin, RB port change, or
data EEPROM write complete.
WAKE-UP FROM SLEEP
Interrupt Latency
Dummy cycle
(Note 2)
PC + 2
Q1 Q2 Q3 Q4
1998 Microchip Technology Inc.
Inst(0004h)
Dummy cycle
0004h
Q1 Q2 Q3 Q4
Inst(0005h)
Inst(0004h)
0005h
is not