PIC24HJ128GP504-I/ML Microchip Technology, PIC24HJ128GP504-I/ML Datasheet - Page 11

• Manufacturer Part Number: PIC24HJ128GP504-I/ML
• Description: IC PIC MCU FLASH 128K 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ128GP504-I/ML

• Core Size: 16-Bit
• Program Memory Size: 128KB (43K x 24)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 13x10b/12b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Controller Family/series: PIC24
• No. Of I/o's: 35
• Ram Memory Size: 8192Byte
• Cpu Speed: 40MHz
• No. Of Timers: 7
• No.: RoHS Compliant
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 9
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 13 Channel
• A/d Bit Size: 12 bit
• A/d Channels Available: 13
• Height: 0.88 mm
• Length: 8 mm
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Width: 8 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDAC164336 - MODULE SOCKET FOR PM3 28/44QFNDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

FIGURE 3-4:
© 2010 Microchip Technology Inc.
BaseAddress + 0x80
BaseAddress =
No
RemainingCmds = 1368
RemainingCmds =
RemainingCmds – 1
BaseAddress = 0x0
Command to Program
FLOWCHART FOR
PROGRAMMING CODE
MEMORY
RemainingCmds
BaseAddress
PROGP response
Send PROGP
PASS?
Start
‘0’?
End
Is
Is
Yes
Yes
Report Error
No
Failure
3.5.2
After code memory is programmed, the contents of
memory can be verified to ensure that programming
was successful. Verification requires code memory to
be read back and compared against the copy held in
the programmer’s buffer.
The READP command can be used to read back all the
programmed code memory.
Alternatively, you can have the programmer perform
the verification after the entire device is programmed,
using a checksum computation.
3.5.3
Only the Configuration registers are included in the
checksum computation. The Device ID and Unit ID are
not included in the checksum computation.
TABLE D-1: “CHECKSUM COMPUTATION”
how this 16-bit computation can be made for each
dsPIC33F and PIC24H device. Computations for read
code protection are shown both enabled and disabled.
The checksum values shown here assume that the
Configuration registers are also erased. However,
when code protection is enabled, the value of the FGS
register is assumed to be 0x5.
PROGRAMMING VERIFICATION
CHECKSUM COMPUTATION
DS70152H-page 11
shows