PIC18F4220-I/P Microchip Technology, PIC18F4220-I/P Datasheet - Page 2

• Manufacturer Part Number: PIC18F4220-I/P
• Description: IC MCU FLASH 2KX16 A/D 40-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4220-I/P

• Program Memory Type: FLASH
• Program Memory Size: 4KB (2K x 16)
• Package / Case: 40-DIP (0.600", 15.24mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 36
• Eeprom Size: 256 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 13x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 10-bit
• Package: 40PDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Data Rom Size: 256 B
• A/d Bit Size: 10 bit
• A/d Channels Available: 13
• Height: 3.81 mm
• Length: 52.26 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.2 V
• Width: 13.84 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP400 - DEVICE ADAPTER 18F4220 PDIP 40LD444-1001 - DEMO BOARD FOR PICMICRO MCUACICE0206 - ADAPTER MPLABICE 40P 600 MIL
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F2220/2320/4220/4320
2. Module: MSSP (All I
DS80396B-page 2
The Buffer Full flag bit (BF) of the SSPSTAT regis-
ter (SSPSTAT<0>) may be inadvertently cleared,
even when the SSPBUF register has not been
read. This will occur only when the following two
conditions occur simultaneously:
• The four Least Significant bits of the BSR
• Any instruction that contains C9h in its 8 Least
Work around
Identified work arounds will involve setting the
contents of BSR<3:0> to some value other than
0Fh.
In addition to those proposed below, other solutions
may exist.
1. When developing or modifying code, keep
2. If accessing a part of Bank 15 is required and
3. If pointing the BSR to Bank 15 is unavoidable,
Date Codes that pertain to this issue:
All engineering and production devices.
register are equal to 0Fh (BSR<3:0> = 1111)
and
Significant bits (i.e., register file addresses,
literal data, address offsets, etc.) is executed.
these guidelines in mind:
• Assign 12-bit addresses to all variables.
• Do not set the BSR to point to Bank 15
• Allow the assembler to manipulate the
the use of Access Banking is not possible,
consider using indirect addressing.
review the absolute file listing. Verify that no
instructions contain C9h in the 8 Least Signifi-
cant bits while the BSR points to Bank 15
(BSR = 0Fh).
This allows the assembler to know when
Access Banking can be used.
(BSR = 0Fh).
Access bit present in most instructions.
Accessing the SFRs in Bank 15 will be done
through the Access Bank. Continue to use
the BSR to select all GPR Banks.
2
C™ and SPI Modes)
3. Module: MSSP (SPI, Slave Mode)
In its current implementation, the SS (Slave
Select) control signal generated by an external
master processor may not be successfully recog-
nized by the PIC
Slave Select mode (SSPM3:SSPM0 = 0100). In
particular, it has been observed that faster transi-
tions (those with shorter fall times) are more likely
to be missed than slower transitions.
Work around
Insert a series resistor between the source of the
SS signal and the corresponding SS input line of
the microcontroller. The value of the resistor is
dependent on both the application system’s
characteristics and process variations between
microcontrollers. Experimentation and thorough
testing is encouraged.
This is a recommended solution; others may exist.
Date Codes that pertain to this issue:
All engineering and production devices.
®
© 2009 Microchip Technology Inc.
microcontroller operating in