PIC18F4220-I/ML Microchip Technology, PIC18F4220-I/ML Datasheet - Page 2
![IC MCU FLASH 2KX16 EEPROM 44QFN](/photos/6/81/68122/150-44-qfn_sml.jpg)
PIC18F4220-I/ML
Manufacturer Part Number
PIC18F4220-I/ML
Description
IC MCU FLASH 2KX16 EEPROM 44QFN
Manufacturer
Microchip Technology
Series
PIC® 18Fr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC18F1320-ISS.pdf
(36 pages)
3.PIC18F2220-ISO.pdf
(394 pages)
4.PIC18F2220-ISO.pdf
(6 pages)
5.PIC18F2220-ISO.pdf
(6 pages)
6.PIC18F2220-ISO.pdf
(8 pages)
7.PIC18F2220-ISO.pdf
(6 pages)
8.PIC18F2220-ISO.pdf
(6 pages)
Specifications of PIC18F4220-I/ML
Core Size
8-Bit
Program Memory Size
4KB (2K x 16)
Core Processor
PIC
Speed
40MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, LVD, POR, PWM, WDT
Number Of I /o
36
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
512 x 8
Voltage - Supply (vcc/vdd)
4.2 V ~ 5.5 V
Data Converters
A/D 13x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
44-QFN
Controller Family/series
PIC18
No. Of I/o's
36
Eeprom Memory Size
256Byte
Ram Memory Size
512Byte
Cpu Speed
40MHz
No. Of Timers
4
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
For Use With
XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN444-1001 - DEMO BOARD FOR PICMICRO MCU
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Contains lead / RoHS non-compliant
PIC18F2220/2320/4220/4320
2. Module: MSSP (All I
DS80396B-page 2
The Buffer Full flag bit (BF) of the SSPSTAT regis-
ter (SSPSTAT<0>) may be inadvertently cleared,
even when the SSPBUF register has not been
read. This will occur only when the following two
conditions occur simultaneously:
• The four Least Significant bits of the BSR
• Any instruction that contains C9h in its 8 Least
Work around
Identified work arounds will involve setting the
contents of BSR<3:0> to some value other than
0Fh.
In addition to those proposed below, other solutions
may exist.
1. When developing or modifying code, keep
2. If accessing a part of Bank 15 is required and
3. If pointing the BSR to Bank 15 is unavoidable,
Date Codes that pertain to this issue:
All engineering and production devices.
register are equal to 0Fh (BSR<3:0> = 1111)
and
Significant bits (i.e., register file addresses,
literal data, address offsets, etc.) is executed.
these guidelines in mind:
• Assign 12-bit addresses to all variables.
• Do not set the BSR to point to Bank 15
• Allow the assembler to manipulate the
the use of Access Banking is not possible,
consider using indirect addressing.
review the absolute file listing. Verify that no
instructions contain C9h in the 8 Least Signifi-
cant bits while the BSR points to Bank 15
(BSR = 0Fh).
This allows the assembler to know when
Access Banking can be used.
(BSR = 0Fh).
Access bit present in most instructions.
Accessing the SFRs in Bank 15 will be done
through the Access Bank. Continue to use
the BSR to select all GPR Banks.
2
C™ and SPI Modes)
3. Module: MSSP (SPI, Slave Mode)
In its current implementation, the SS (Slave
Select) control signal generated by an external
master processor may not be successfully recog-
nized by the PIC
Slave Select mode (SSPM3:SSPM0 = 0100). In
particular, it has been observed that faster transi-
tions (those with shorter fall times) are more likely
to be missed than slower transitions.
Work around
Insert a series resistor between the source of the
SS signal and the corresponding SS input line of
the microcontroller. The value of the resistor is
dependent on both the application system’s
characteristics and process variations between
microcontrollers. Experimentation and thorough
testing is encouraged.
This is a recommended solution; others may exist.
Date Codes that pertain to this issue:
All engineering and production devices.
®
© 2009 Microchip Technology Inc.
microcontroller operating in