PIC16C76-20I/SP Microchip Technology, PIC16C76-20I/SP Datasheet - Page 119
![IC MCU OTP 8KX14 A/D PWM 28DIP](/photos/6/59/65908/150-28-dip_sml.jpg)
PIC16C76-20I/SP
Manufacturer Part Number
PIC16C76-20I/SP
Description
IC MCU OTP 8KX14 A/D PWM 28DIP
Manufacturer
Microchip Technology
Series
PIC® 16Cr
Datasheets
1.PIC16F616T-ISL.pdf
(8 pages)
2.PIC16F818-ISO.pdf
(6 pages)
3.PIC16C63A-04SP.pdf
(184 pages)
4.PIC16C72-04SO.pdf
(289 pages)
5.PIC16C76-04SP.pdf
(8 pages)
Specifications of PIC16C76-20I/SP
Core Size
8-Bit
Program Memory Size
14KB (8K x 14)
Core Processor
PIC
Speed
20MHz
Connectivity
I²C, SPI, UART/USART
Peripherals
Brown-out Detect/Reset, POR, PWM, WDT
Number Of I /o
22
Program Memory Type
OTP
Ram Size
368 x 8
Voltage - Supply (vcc/vdd)
4 V ~ 6 V
Data Converters
A/D 5x8b
Oscillator Type
External
Operating Temperature
-40°C ~ 85°C
Package / Case
28-DIP (0.300", 7.62mm)
Controller Family/series
PIC16C
No. Of I/o's
22
Ram Memory Size
368Byte
Cpu Speed
10MHz
No. Of Timers
3
Interface
I2C, SPI, USART
Embedded Interface Type
I2C, SPI, USART
Rohs Compliant
Yes
Package
28SPDIP
Device Core
PIC
Family Name
PIC16
Maximum Speed
20 MHz
Operating Supply Voltage
5 V
Data Bus Width
8 Bit
Number Of Programmable I/os
22
Interface Type
I2C/SPI/USART
On-chip Adc
5-chx8-bit
Number Of Timers
3
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Note 1: This is the limit to which V
PIC16LC63A/65B/73B/74B-04
‡
‡
D040
D040A
D041
D042
D042A
D043
D060
D061
D063
D070
Param
PIC16C63A/65B/73B/74B-04
PIC16C6A/65B/73B/74B-20
* These parameters are characterized but not tested.
† Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and
‡ When specification values of standard devices differ from those of extended voltage devices, they are shown in gray.
2000 Microchip Technology Inc.
No.
are not tested.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is mea-
4: For RC osc mode, current through R
5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from character-
6: The
7: When BOR is enabled, the device will operate correctly until the V
8: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the
9: The leakage current on the MCLR/V
10: Negative current is defined as current sourced by the pin.
loading and switching rate, oscillator type, internal code execution pattern and temperature also have an impact
on the current consumption. The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to V
MCLR = V
sured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
the formula Ir = V
ization and is for design guidance only. This is not tested.
added to the base I
PICmicro device be driven with external clock in RC mode.
els represent normal operating conditions. Higher leakage current may be measured at different input voltages.
I
Sym
PURB
V
I
IL
IH
current is the additional current consumed when this peripheral is enabled. This current should be
Input High Voltage
I/O ports
MCLR
OSC1 (in XT, HS, and
LP modes)
OSC1 (in RC mode)
Input Leakage
Current (Notes 9, 10)
I/O ports
MCLR, RA4/T0CKI
OSC1
PORTB Weak Pull-up
Current
DD
Characteristic
with TTL buffer
with Schmitt
Trigger buffer
; WDT enabled/disabled as specified.
DD
DD
/2R
or I
EXT
PD
DD
(mA) with R
measurement.
can be lowered without losing RAM data.
0.25 V
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Standard Operating Conditions (unless otherwise stated)
Operating temperature
0.8 V
0.8 V
0.7 V
0.9 V
0.8V
Min
2.0
50
PP
–
–
–
EXT
DD
DD
DD
DD
DD
pin is strongly dependent on the applied voltage level. The specified lev-
EXT
+
is not included. The current through the resistor can be estimated by
Typ†
250
PIC16C63A/65B/73B/74B
in kOhm.
–
–
–
–
–
–
–
–
–
Max
V
V
V
V
V
V
400
±1
±5
±5
DD
DD
DD
DD
DD
DD
DD
-40°C
-40°C
-40°C
measurements in active operation mode are:
Units
0°C
0°C
V
V
V
V
V
V
A
A
A
A
4.5 V
For entire V
For entire V
(Note 8)
Vss
Pin at hi-impedance
Vss
Vss
XT, HS and LP osc modes
V
BOR
T
T
T
T
T
DD
A
A
A
A
A
= 5V, V
voltage trip point is reached.
V
V
V
+125°C
V
PIN
PIN
PIN
+70°C
+85°C
+70°C
+85°C
DD
DD
DD
PIN
V
V
V
DD
5.5V
DD
DD
DD
range
range
= V
Conditions
,
,
,
for commercial
for industrial
for commercial
for industrial
for extended
SS
DD
DS30605C-page 119
and V
SS
.