PIC18F2685-I/SP Microchip Technology, PIC18F2685-I/SP Datasheet - Page 201

• Manufacturer Part Number: PIC18F2685-I/SP
• Description: IC PIC MCU FLASH 48KX16 28-DIP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2685-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 96KB (48K x 16)
• Package / Case: 28-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Eeprom Size: 1K x 8
• Ram Size: 3.25K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.25 KB
• Interface Type: EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 28
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 28SPDIP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Operating Supply Voltage: 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DVA18XP280 - DEVICE ADAPTER 18F2220 PDIP 28LD
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 17-5:
© 2009 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
R/W-0
GCEN
2:
Value that will be transmitted when the user initiates an Acknowledge sequence at the end of a receive.
For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I
set (no spooling) and the SSPBUF may not be written (or writes to the SSPBUF are disabled).
GCEN: General Call Enable bit (Slave mode only)
1 = Enable interrupt when a general call address (0000h) is received in the SSPSR
0 = General call address disabled
ACKSTAT: Acknowledge Status bit (Master Transmit mode only)
1 = Acknowledge was not received from slave
0 = Acknowledge was received from slave
ACKDT: Acknowledge Data bit (Master Receive mode only)
1 = Not Acknowledge
0 = Acknowledge
ACKEN: Acknowledge Sequence Enable bit (Master Receive mode only)
1 = Initiate Acknowledge sequence on SDA and SCL pins and transmit ACKDT data bit. Automatically
0 = Acknowledge sequence Idle
RCEN: Receive Enable bit (Master mode only)
1 = Enables Receive mode for I
0 = Receive Idle
PEN: Stop Condition Enable bit (Master mode only)
1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
RSEN: Repeated Start Condition Enable bit (Master mode only
1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
SEN: Start Condition Enable/Stretch Enable bit
In Master mode:
1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
In Slave mode:
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled
ACKSTAT
R/W-0
cleared by hardware.
SSPCON2: MSSP CONTROL REGISTER 2 (I
W = Writable bit
‘1’ = Bit is set
ACKDT
R/W-0
(1)
PIC18F2682/2685/4682/4685
ACKEN
2
R/W-0
C
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
2
RCEN
C module is not in the Idle mode, these bits may not be
R/W-0
(2)
(2)
(2)
(2)
2
C™ MODE)
(1)
PEN
R/W-0
(2)
(2)
x = Bit is unknown
(2)
RSEN
R/W-0
(2)
DS39761C-page 201
SEN
R/W-0
(2)
bit 0