Z16F3211AL20SG Zilog, Z16F3211AL20SG Datasheet - Page 173

• Manufacturer Part Number: Z16F3211AL20SG
• Description: IC ZNEO MCU FLASH 32K 100LQFP
• Manufacturer: Zilog
• Series: Encore!® ZNEOr

Specifications of Z16F3211AL20SG

• Core Processor: ZNEO
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: EBI/EMI, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 76
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 100-LQFP
• Processor Series: Z16F3x
• Core: Zneo
• Data Bus Width: 16 bit
• Data Ram Size: 2 B
• Interface Type: ESPI, I2C, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 76
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: Z16F2800100ZCOG
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 770-1003 - ISP 4PORT FOR ZILOG ZNEO MCU269-4537 - DEV KIT FOR Z16F ZNEO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4568

Table 84. LIN-UART Mode Select and Status Register (UxMDSTAT)
PS022008-0810
BITS
FIELD
RESET
R/W
ADDR
LIN-UART Mode Select and Status Register
R/W
7
0
This register contains mode select and status bits.
MSEL—Mode Select 
This R/W field determines which control register is accessed when performing a Write or
Read to the UART Control 1 register address. This field also determines which status is
returned in the mode status field when reading this register.
000 = Multiprocessor and normal UART control/status
001 = Noise Filter control/status
010 = LIN Protocol control/status
011–110: Reserved
111 = LIN-UART hardware revision (allows hardware revision to be read in the mode
Mode Status—This read-only field returns status corresponding to the mode selected by
MSEL
000: MULTIPROCESSOR and NORMAL UART mode status = {
001: Noise filter status = {
010: LIN mode status = {
011–110: Reserved =
111: LIN-UART hardware revision
MULTIPROCESSOR Mode Status field (MSEL = 000B)
NE—Noise Event
This bit is asserted if digital noise is detected on the receive data line when the data is
sampled (center of bit time). If this bit is set, it does not mean that the receive data is
corrupted (in extreme cases), just that one or more of the noise filter data samples near the
center of the bit time did not match the average data value.
NEWFRM—Status bit denoting the start of a new frame. Reading the LIN-UART receive
data register Resets this bit to 0.
MPRX
as follows:
status field)
MSEL
}
R/W
6
0
{0, 0, 0, 0, 0}
R/W
5
0
NE, RxBreakLength[3:0
NE
P R E L I M I N A R Y
,
FF-E204H, FF-E214H
0,0,0,0}
R
4
0
R
3
0
Mode Status
]}
R
2
0
Product Specification
NE
ZNEO
,
0, 0, NEWFRM,
1
R
0
Z16F Series
LIN-UART
R
0
0
157