STM32F101CBT6 STMicroelectronics, STM32F101CBT6 Datasheet - Page 77

• Manufacturer Part Number: STM32F101CBT6
• Description: MCU ARM 32KB FLASH/TIMER 48LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F101CBT6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 36MHz
• Connectivity: I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: DMA, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 37
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-LQFP
• Processor Series: STM32F101x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/SPI/USART
• Maximum Clock Frequency: 36 MHz
• Number Of Programmable I/os: 37
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 12-bit
• Controller Family/series: (ARM Cortex) STM32
• No. Of I/o's: 37
• Ram Memory Size: 16KB
• Cpu Speed: 36MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• For Use With: 497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6287

STM32F101x8, STM32F101xB
6.2.2
Evaluating the maximum junction temperature for an application
When ordering the microcontroller, the temperature range is specified in the ordering
information scheme shown in
Each temperature range suffix corresponds to a specific guaranteed ambient temperature at
maximum dissipation and, to a specific maximum junction temperature. Here, only
temperature range 6 is available (–40 to 85 °C).
The following example shows how to calculate the temperature range needed for a given
application, making it possible to check whether the required temperature range is
compatible with the STM32F101xx junction temperature range.
Example: high-performance application
Assuming the following application conditions:
Thus: P
Using the values obtained in
This is within the junction temperature range of the STM32F101xx (–40 < T
Figure 47. LQFP64 P
Maximum ambient temperature T
I
level with I
mode at low level with I
P
P
This gives: P
P
–
T
DDmax
Jmax
INTmax
IOmax
Dmax
Dmax
For LQFP64, 45 °C/W
= 82 °C + (45 °C/W × 447 mW) = 82 °C + 20.1 °C = 102.1 °C
= 175 + 272 = 447 mW
= 50 mA, V
= 20 × 8 mA × 0.4 V + 8 × 20 mA × 1.3 V = 272 mW
= 447 mW
= 50 mA × 3.5 V= 175 mW
700
600
500
400
300
200
100
OL
0
INTmax
= 8 mA, V
65
DD
D
= 175 mW and P
max vs. T
= 3.5 V, maximum 20 I/Os used at the same time in output at low
75
OL
OL
Table 51
Doc ID 13586 Rev 13
Table 52: Ordering information
= 0.4 V and maximum 8 I/Os used at the same time in output
= 20 mA, V
85
A
T
Amax
T
A
Jmax
(°C)
IOmax
OL
= 82 °C (measured according to JESD51-2),
95
is calculated as follows:
= 1.3 V
= 272 mW
105
115
scheme.
Package characteristics
Suffix 6
J
< 105 °C).
77/85