STM32F103RET6 STMicroelectronics, STM32F103RET6 Datasheet - Page 83

• Manufacturer Part Number: STM32F103RET6
• Description: MCU ARM 512KB FLASH MEM 64-LQFP
• Manufacturer: STMicroelectronics
• Series: STM32r

Specifications of STM32F103RET6

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 72MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB
• Peripherals: DMA, Motor Control PWM, PDR, POR, PVD, PWM, Temp Sensor, WDT
• Number Of I /o: 51
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• Processor Series: STM32F103x
• Core: ARM Cortex M3
• Data Bus Width: 32 bit
• Data Ram Size: 64 KB
• Interface Type: CAN, I2C, SPI, USART
• Maximum Clock Frequency: 72 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 8
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWARM, EWARM-BL, MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 3 (12 bit, 16 Channel)
• On-chip Dac: 2 (12 bit, 2 Channel)
• For Use With: 497-10508 - BOARD EVAL FOR MEMS SENSORS497-10048 - BOARD EVAL ACCELEROMETER497-10030 - STARTER KIT FOR STM32497-8853 - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL - KIT IAR KICKSTART STM32 CORTEXM3497-8512 - KIT STARTER FOR STM32F10XE MCU497-8511 - KIT STARTER FOR STM32 512K FLASH497-8505 - KIT STARTER FOR STM32F10XE MCU497-8304 - KIT STM32 MOTOR DRIVER BLDC497-6438 - BOARD EVALUTION FOR STM32 512K497-6289 - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U - BOARD EVAL MCBSTM32 + ULINK2MCBSTM32 - BOARD EVAL FOR STM STM32X SER497-6053 - KIT STARTER FOR STM32497-6052 - KIT STARTER FOR STM32497-6050 - KIT STARTER FOR STM32497-6049 - KIT EVALUATION LOW COST STM32497-6048 - BOARD EVALUATION FOR STM32497-6047 - KIT DEVELOPMENT FOR STM32497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-6444

STM32F103xC, STM32F103xD, STM32F103xE
All I/Os are CMOS and TTL compliant (no software configuration required), their
characteristics consider the most strict CMOS-technology or TTL parameters:
●
●
Output driving current
The GPIOs (general purpose input/outputs) can sink or source up to +/-8 mA, and sink
+20 mA (with a relaxed V
In the user application, the number of I/O pins which can drive current must be limited to
respect the absolute maximum rating specified in
●
●
Output voltage levels
Unless otherwise specified, the parameters given in
performed under ambient temperature and V
Table
For V
–
–
For V
–
–
The sum of the currents sourced by all the I/Os on V
consumption of the MCU sourced on V
I
The sum of the currents sunk by all the I/Os on V
consumption of the MCU sunk on V
I
VDD
VSS
10. All I/Os are CMOS and TTL compliant.
if V
if V
if V
if V
(see
(see
IH
IL
:
:
DD
DD
DD
DD
Table
Table
is in the [2.00 V - 3.08 V] range: CMOS characteristics but TTL included
is in the [3.08 V - 3.60 V] range: TTL characteristics but CMOS included
is in the [2.00 V - 2.28 V] range: TTL characteristics but CMOS included
is in the [2.28 V - 3.60 V] range: CMOS characteristics but TTL included
8).
8).
OL
).
Doc ID 14611 Rev 7
SS
DD,
cannot exceed the absolute maximum rating
DD
cannot exceed the absolute maximum rating
supply voltage conditions summarized in
Section
Table 46
SS
plus the maximum Run
DD,
5.2:
plus the maximum Run
are derived from tests
Electrical characteristics
83/123