C8051F305-GM Silicon Laboratories Inc, C8051F305-GM Datasheet - Page 144

• Manufacturer Part Number: C8051F305-GM
• Description: IC 8051 MCU 2K FLASH 11QFN
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F30xr

Specifications of C8051F305-GM

• Program Memory Type: FLASH
• Program Memory Size: 2KB (2K x 8)
• Package / Case: 11-VQFN
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Processor Series: C8051F3x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C/SMBus/UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 8
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F300DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8 bit, 8 Channel
• No. Of I/o's: 8
• Ram Memory Size: 256Byte
• Cpu Speed: 25MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 11QFN EP
• Device Core: 8051
• Family Name: C8051F30x
• Maximum Speed: 25 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 770-1006 - ISP 4PORT FOR SILABS C8051F MCU336-1444 - ADAPTER PROGRAM TOOLSTICK F300
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1251

C8051F300/1/2/3/4/5
The C/T0 bit (TMOD.2) selects the counter/timer's clock source. When C/T0 is set to logic 1, high-to-low
transitions at the selected Timer 0 input pin (T0) increment the timer register (Refer to
“12.1. Priority Crossbar Decoder” on page 104
pins). Clearing C/T selects the clock defined by the T0M bit (CKCON.3). When T0M is set, Timer 0 is
clocked by the system clock. When T0M is cleared, Timer 0 is clocked by the source selected by the Clock
Scale bits in CKCON (see SFR Definition 15.3).
Setting the TR0 bit (TCON.4) enables the timer when either GATE0 (TMOD.3) is logic 0 or the input signal
/INT0 is active as defined by bit IN0PL in register IT01CF (see SFR Definition 8.11). Setting GATE0 to ‘1’
allows the timer to be controlled by the external input signal /INT0 (see
Descriptions” on page
Setting TR0 does not force the timer to reset. The timer registers should be loaded with the desired initial
value before the timer is enabled.
TL1 and TH1 form the 13-bit register for Timer 1 in the same manner as described above for TL0 and TH0.
Timer 1 is configured and controlled using the relevant TCON and TMOD bits just as with Timer 0. The
input signal /INT1 is used with Timer 1; the /INT1 polarity is defined by bit IN1PL in register IT01CF (see
SFR Definition 8.11).
144
/INT0
T0
Crossbar
Pre-scaled Clock
SYSCLK
IN0PL
GATE0
75), facilitating pulse width measurements.
*Note: X = Don't Care
XOR
Figure 15.1. T0 Mode 0 Block Diagram
TR0
0
1
1
1
TR0
0
1
M
T
H
2
GATE0
CKCON
M
T
2
L
X*
M
T
1
0
1
1
0
1
M
T
0
C
S
A
1
S
C
A
Rev. 2.9
0
for information on selecting and configuring external I/O
G
A
T
E
1
/INT0
C
T
1
/
X*
X*
0
1
M
T
1
1
TMOD
M
T
1
0
TCLK
G
A
T
E
0
C
T
0
/
M
T
0
1
Counter/Timer
M
T
0
0
(5 bits)
TL0
Disabled
Disabled
Enabled
Enabled
N
P
1
L
I
N
S
1
L
2
I
Section “8.3.5. Interrupt Register
IT01CF
N
1
S
L
1
I
N
S
1
L
0
I
N
0
P
L
(8 bits)
I
TH0
N
S
0
L
2
I
N
0
S
L
1
I
N
S
0
L
0
I
TR1
TR0
TF1
TF0
IE1
IE0
IT1
IT0
Section
Interrupt